1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Front License Plate Holes

Discussion in 'Gen 3 Prius Accessories and Modifications' started by unit333, Jan 22, 2010.

  1. unit333

    unit333 Junior Member

    Joined:
    Dec 20, 2009
    77
    7
    0
    Location:
    NYC
    Vehicle:
    2010 Prius
    Model:
    II
    Any specific instructions on how to drill the holes in my 2010 Prius for the front plate? The only thing I wanna know is what's under the bumper so I don't mess it up. I am also going to a toyota dealer tomorrow for safety inspection so I guess I can ask them to do it for me.

    What do you guys think?
     
    #1 unit333, Jan 22, 2010
  2. Judgeless

    Judgeless Senior Member

    Joined:
    Jun 30, 2009
    1,821
    255
    0
    Location:
    Cleveland, OH
    Vehicle:
    2010 Prius
    Model:
    IV
    Mine came with a mount with screw holes.
     
    #2 Judgeless, Jan 22, 2010
  3. boppo

    boppo Active Member

    Joined:
    Mar 11, 2009
    799
    138
    0
    Location:
    Owego, NY
    Vehicle:
    2006 Prius
    Model:
    II
    on my 2006 there were 2 dimples in the bumper and the front plate bracket came with the hardware.
     
    #3 boppo, Jan 22, 2010
  4. Judgeless

    Judgeless Senior Member

    Joined:
    Jun 30, 2009
    1,821
    255
    0
    Location:
    Cleveland, OH
    Vehicle:
    2010 Prius
    Model:
    IV
    Here are some pic of the one that came with my car. My car is very dirty.

    [​IMG]

    [​IMG]
     
    #4 Judgeless, Jan 22, 2010
  5. hyo silver

    hyo silver Awaaaaay

    Joined:
    Mar 2, 2005
    15,232
    1,563
    0
    Location:
    off into the sunset
    Vehicle:
    2004 Prius
    Model:
    N/A
    The dealer could do it for you, but you'd likely take better care in getting it perfectly straight. There's mostly styrofoam behind the 'bumper', so don't worry about drilling into it. The plastic is soft enough that you can drive the screws without drilling a pilot hole, but it's easier to find the right spot if you do.

    The plate holder might be in the trunk, if you haven't already found it. If not, the dealer should give you one.
     
    #5 hyo silver, Jan 22, 2010
  6. Joe166

    Joe166 New Member

    Joined:
    Dec 19, 2009
    720
    96
    0
    Location:
    South Florida
    Vehicle:
    Other Hybrid
    Model:
    V
    I bet the plate holder is in the bottom trunk, near the compact spare tire. Has the screws, the plate holder enclosed in a clear plastic cover. Mine was over to the side in one of the cubby holes.
     
    #6 Joe166, Jan 22, 2010
  7. KK6PD

    KK6PD _ . _ . / _ _ . _

    Joined:
    Mar 24, 2008
    4,003
    944
    118
    Location:
    Los Angeles Foothills
    Vehicle:
    Other Hybrid
    Model:
    N/A
    Get a couple of # 8 or #10 - 3/4 inch or so Stainless Steel Panhead screws, if they are not all ready incuded with the plate mount, chuck up a 1/8 inch bit, drill a pilot hole into the plastic until it just pops thru, screw it in.
    That's all the dealer did for me.
    Hopefully you can mount yours straighter than my dealer, or whoever, did to my car!!!
    I wish they would have just let me do it, instead of me redoing it!!!
     
    #7 KK6PD, Jan 22, 2010
  8. unit333

    unit333 Junior Member

    Joined:
    Dec 20, 2009
    77
    7
    0
    Location:
    NYC
    Vehicle:
    2010 Prius
    Model:
    II
    Thanks everyone. Yeah i have the whole set with screws and the car came with markers which indicate where to drill so it shouldnt be too complicated;)
     
    #8 unit333, Jan 23, 2010
  9. eight08customs

    eight08customs Senior Member

    Joined:
    Nov 2, 2009
    245
    583
    0
    Location:
    Hawaii
    Vehicle:
    2016 Prius
    Model:
    Two
    if you dont want to drill holes in your bumper I make a Lic plate bracket that will prob work.. Its for the Scion but the Prius has the same type of grill.

    www.eight08customs.com
     
    #9 eight08customs, Jan 26, 2010
  10. jukeboy

    jukeboy New Member

    Joined:
    Mar 14, 2005
    132
    4
    0
    Location:
    SGV, SoCal
    Vehicle:
    2010 Prius
    Model:
    II
    my problem is the opposite of yours: plugging the existing holes; relocated my plate using a tilting bracket from autozone for $9 and some zip ties...

    [​IMG]

    seen your work on the scion forums... would be interesting to have other stuff like grille garnishments for the prius as well
     
    #10 jukeboy, Jan 29, 2010
  11. shankyyy

    shankyyy Member

    Joined:
    Jul 25, 2009
    172
    8
    0
    Location:
    Charlotte, NC
    Vehicle:
    2010 Prius
    Model:
    III
    Is it really necessary to drill the two holes in the bumper cover? As i see it, the mounting bracket fits is screwed onto the dimples in the bumper using the tapping screws provided by Toyota. And it appears the license plate can be screwed onto the mounting bracket in the threaded slots. So, in essence the plate is attached to the bracket, which is attached to the bumper. Besides a more snug and tight fit, cannot see why the license plate needs to be screwed all the way into the bumper. any thoughts would help as it's time for me to fit my plates.
     
    #11 shankyyy, Feb 20, 2010
(You must log in or sign up to post here.)