1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Warning lights ((!)) --> not able to get in ready mode

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by nusskiller, Sep 28, 2013.

  1. nusskiller

    nusskiller Junior Member

    Joined:
    May 30, 2013
    7
    0
    0
    Location:
    Sacramento, CA
    Vehicle:
    2006 Prius
    Model:
    N/A
    Hi there,
    when I backed up yesterday, some dash symbols showed up. After turning off the car, I am not able to get it in Ready Mode. Only solution so far: to disconnect the 12V battery and wait approx. 2-3 minutes. After that, the lights are off. The 12v battery does also indicates normal voltage. IG-OFF: 12.7V IG-ON 12.2
    Any ideas? Unfortunately I cannot get the trouble codes with my scan tool :-(
     

    Attached Files:

    #1 nusskiller, Sep 28, 2013
  2. Prius_Cub

    Prius_Cub Member

    Joined:
    Feb 12, 2013
    152
    60
    0
    Location:
    Radford, VA
    Vehicle:
    2008 Prius
    Model:
    II
    Seeing lower voltage in READY shouldn't be possible, should jump up to around 14 volts as the 12 gets recharged...unless something is wrong with the DC-DC converter. Are you sure that was in READY mode?
    As far as the issue itself, maybe someone else here has had/seen the issue and will be along shortly.

    Edit: I was skimming too fast to read that the 12.2 was in IG-ON and you couldn't get to READY. My bad :/
    HTC Evo 3D
     
    #2 Prius_Cub, Sep 28, 2013
  3. nh7o

    nh7o Off grid since 1980

    Joined:
    Dec 10, 2011
    1,686
    338
    0
    Location:
    Hawaii
    Vehicle:
    2009 Prius
    Model:
    II
    Unfortunately, all those icons don't give any good indication of the source of the problem. Only a Prius capable scanner will give the sort of info that can return good advice. However, if the problem happens again you can try getting "blink codes" from the ABS system. Do a search for blink codes for more info, but the short direction is to short pin 4 and 13 of the OBDII connector, and then make the car ready. Look at the series of blinks in the icons, and list them here.

    Did the lights come on when you applied the brakes? Try listening for the brake actuator motor when you step on the brake pedal, and see if it is making any unusual noise.
     
    #3 nh7o, Sep 28, 2013
  4. nusskiller

    nusskiller Junior Member

    Joined:
    May 30, 2013
    7
    0
    0
    Location:
    Sacramento, CA
    Vehicle:
    2006 Prius
    Model:
    N/A
    The lights do not come on every time I apply the brake. Today I disconnected the battery, then we had been driving for about 15 miles, when the lights came up again. Everything works as normal. The battery is being charged, the brake system seems to work properly as well. When I try to force the problem by pushing the brake pedal, it does not work.
    I will try to get the blink codes tomorrow or later today.
     
    #4 nusskiller, Sep 28, 2013
  5. nusskiller

    nusskiller Junior Member

    Joined:
    May 30, 2013
    7
    0
    0
    Location:
    Sacramento, CA
    Vehicle:
    2006 Prius
    Model:
    N/A
    Ok, got some blink codes, hope this helps.
    ((!)) and ABS and tire pressure and air bag started to blinking in IG-ON.
    ABS and tire pressure and air bag continued blinking while ((!)) started the following cycle: 5 - pause - 8 - pause - 5 - pause - 8 - pause...
     
    #5 nusskiller, Sep 28, 2013
  6. nusskiller

    nusskiller Junior Member

    Joined:
    May 30, 2013
    7
    0
    0
    Location:
    Sacramento, CA
    Vehicle:
    2006 Prius
    Model:
    N/A
    After trying to get in Ready, I hear 5 beeps pause and one more beep... Maybe this also helps
     
    #6 nusskiller, Sep 28, 2013
  7. Patrick Wong

    Patrick Wong DIY Enthusiast

    Joined:
    Mar 8, 2008
    18,200
    6,471
    0
    Location:
    Green Valley, AZ
    Vehicle:
    2015 Prius
    Model:
    Two
    This translated to DTC C1259, which means the skid control ECU cannot communicate with the hybrid vehicle ECU. I suggest you seek professional assistance as other DTC probably have been logged which will help to pin down the problem.
     
    #7 Patrick Wong, Sep 28, 2013
    GrumpyCabbie likes this.
(You must log in or sign up to post here.)