1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Move 'Reverse' beeper to back bumper. Anyone done it?

Discussion in 'Gen 3 Prius Accessories and Modifications' started by davekro, Jan 1, 2014.

Page 2 of 2
  1. davekro

    davekro Member

    Joined:
    Oct 23, 2013
    480
    67
    0
    Location:
    SF Bay Area, East Bay
    Vehicle:
    2013 Prius Plug-in
    Model:
    Plug-in Base
    Good to know.
    Also, the TPMS is reprogrammed simply by turning key 'on', then holding TPMS button under dash (next to OBD II connector) until the dash TPMS light blinks three times, then leave on for a few minutes before turning car off.

    Bisco, I can be hard of hearing and reading sometimes too! :p
    I do like the strange sound of the imitation engine. To me it matches the otherworldly characteristics of our new PiP! (y)
     
    #21 davekro, Jan 3, 2014
  2. kenmce

    kenmce High Voltage Member

    Joined:
    May 4, 2004
    1,530
    507
    0
    Location:
    NY
    Vehicle:
    Other Hybrid
    Model:
    Limited
    It may not be practical to move the existing beeper. It may be soldered onto a board under the dash somewhere. If you want, you can tap power from one of the backup bulbs, run a wire under the back of the car, put a beeper there. Maybe just pour hot wax over the existing beeper, be done with it.
     
    #22 kenmce, Jan 3, 2014
  3. davekro

    davekro Member

    Joined:
    Oct 23, 2013
    480
    67
    0
    Location:
    SF Bay Area, East Bay
    Vehicle:
    2013 Prius Plug-in
    Model:
    Plug-in Base
    Yeh, I thought better later about removing the factory beeper under dash. Better to just shut it off and add whatever I might want to the back.
     
    #23 davekro, Jan 3, 2014
  4. Feri

    Feri Active Member

    Joined:
    Jun 25, 2011
    761
    144
    0
    Location:
    Maldon Victoria Australia
    Vehicle:
    2010 Prius
    Model:
    III

    I think you might find that a number of different warning functions use that same beeper unit and it might not be practicable to disable it.
     
    #24 Feri, Jan 4, 2014
  5. Britprius

    Britprius Senior Member

    Joined:
    Jun 14, 2010
    5,194
    1,914
    0
    Location:
    Herefordshire England
    Vehicle:
    2008 Prius
    32K and Feri I apologize regard the resetting of the settings when disconnecting the battery. This is the case with the gen2 and something Toyota has obviously improved on the gen3, but the other points still stand.

    John (Britprius)
     
    #25 Britprius, Jan 4, 2014
  6. Britprius

    Britprius Senior Member

    Joined:
    Jun 14, 2010
    5,194
    1,914
    0
    Location:
    Herefordshire England
    Vehicle:
    2008 Prius
    When I was referring to the TPM system I should have been clearer. If you change wheels for the winter or fit new tyre valves you have to register the valve with the TPMS, and this cannot be done with the buttons under the dash. Unless this has been changed for the gen3.

    John (Britprius)
     
    #26 Britprius, Jan 4, 2014
  7. Feri

    Feri Active Member

    Joined:
    Jun 25, 2011
    761
    144
    0
    Location:
    Maldon Victoria Australia
    Vehicle:
    2010 Prius
    Model:
    III

    No worries mate! We don't have TPMS out here so I no nothing about it.:)
     
    #27 Feri, Jan 4, 2014
(You must log in or sign up to post here.)
Page 2 of 2