any market for a subwoofer enclosure?

Discussion in 'Gen 2 Prius Audio and Electronics' started by hyo silver, May 20, 2009.

Page 2 of 2
  1. F8L

    F8L Protecting Habitat & AG Lands

    Joined:
    Aug 14, 2006
    19,011
    4,083
    50
    Location:
    Grass Valley, CA.
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A
    We're not going for light here buddy. :p We're going for strength!

    Yes, use wood were possible and connect the sections with fiberglass. No PVC needed, we are not building a ported box. That would require more air space. :)
     
    #21 F8L, May 25, 2009
  2. hyo silver

    hyo silver Awaaaaay

    Joined:
    Mar 2, 2005
    15,269
    1,604
    0
    Location:
    off into the sunset
    Vehicle:
    2025 Prius Plug-in
    Model:
    XSE Premium
    This is starting to sound more like a woodwork project and less like a fibreglass project. ;)

    In fact, if I can get flat panels of 1" MDF in there, I may not need fibreglass at all. It's not needed for making the joints airtight, and the box doesn't need to be waterproof. Hmmm. Time to play with some cardboard.
     
    #22 hyo silver, May 25, 2009
  3. Gadgetdad

    Gadgetdad New Member

    Joined:
    Feb 10, 2007
    462
    54
    0
    Location:
    Modesto, California
    Vehicle:
    2010 Prius
    Model:
    IV
    I'd be interested for my '10 if it fits. I'm not into replacing everything else too just to power the sub. Is there an uncomplicated way to "tap" existing amp to run one?

    Lee
     
    #23 Gadgetdad, May 25, 2009
  4. F8L

    F8L Protecting Habitat & AG Lands

    Joined:
    Aug 14, 2006
    19,011
    4,083
    50
    Location:
    Grass Valley, CA.
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A

    LOL you are cracking me up my friend. :)

    3/4" MDF is more than enough for our baby subs. I'm sure you'll use fiberglass as well as wood. it would be much easier to fill in the large gaps between the wood AND you can eek out more air space that way. :)
     
    #24 F8L, May 25, 2009
  5. F8L

    F8L Protecting Habitat & AG Lands

    Joined:
    Aug 14, 2006
    19,011
    4,083
    50
    Location:
    Grass Valley, CA.
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A
    You can easily "tap" into the existing system to feed a signal to the new subwoofer amplifier. :)
     
    #25 F8L, May 25, 2009
  6. hyo silver

    hyo silver Awaaaaay

    Joined:
    Mar 2, 2005
    15,269
    1,604
    0
    Location:
    off into the sunset
    Vehicle:
    2025 Prius Plug-in
    Model:
    XSE Premium
    Well, we could use 2" steel plate. I think jayman has some extra lying around, and apparently he loves to play with a cutting torch.

    But then, I won't be mailing any of these things anywhere, and it would only cut down on the interior volume of the enclosure, which I gather is on the low end of the scale as it is. And MDF's not the densest of woods - maybe I can scrounge up some Lignum Vitae or Ebony.

    Heck, I could even try casting some out of concrete, but then we'd have to put one on each side to balance the car. Unless of course I installed an airbag suspension, which has other advantages, but that's maybe getting a little carried away. :rolleyes:
     
    #26 hyo silver, May 25, 2009
  7. PriusLewis

    PriusLewis Management Scientist

    Joined:
    Feb 25, 2009
    1,002
    84
    7
    Location:
    Denver Metro
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A
    I'd go with forged Titanium, chemically machined to fit. Shouldn't cost more than $100K or so. As for concrete vs steel, during WW II they made boats from concrete that were lighter and stronger than steel. I always wondered how they kept them from leaking, considering every basement I've seen LOL.
     
    #27 PriusLewis, May 26, 2009
  8. ashe

    ashe Junior Member

    Joined:
    May 2, 2009
    34
    1
    13
    Location:
    Newport Beach, CA
    Vehicle:
    2008 Prius
    Model:
    N/A
    interesting read. i'm having a fiberglass sub enclosure made for the passenger side cubby in the hatch. hopefully i'll be able to post some pics this weekend in a new thread.
     
    #28 ashe, May 28, 2009
  9. hyo silver

    hyo silver Awaaaaay

    Joined:
    Mar 2, 2005
    15,269
    1,604
    0
    Location:
    off into the sunset
    Vehicle:
    2025 Prius Plug-in
    Model:
    XSE Premium
    Let us know how it turns out.

    And how much it costs. :cool:
     
    #29 hyo silver, May 28, 2009
  10. Yont283

    Yont283 Junior Member

    Joined:
    Nov 3, 2008
    34
    3
    5
    Location:
    Livonia, MI
    Vehicle:
    2014 Prius v wagon
    Model:
    Two
    i would be interested if the price was not to much.... do you have a price range?
     
    #30 Yont283, May 29, 2009
  11. hyo silver

    hyo silver Awaaaaay

    Joined:
    Mar 2, 2005
    15,269
    1,604
    0
    Location:
    off into the sunset
    Vehicle:
    2025 Prius Plug-in
    Model:
    XSE Premium
    No, it's too early to say. It's looking more likely that I'll just build one for myself.
     
    #31 hyo silver, Jun 2, 2009
(You must log in or sign up to post here.)
Page 2 of 2