1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Help replacing front speakers

Discussion in 'Gen 2 Prius Audio and Electronics' started by phileFriendly, Jul 30, 2005.

  1. phileFriendly

    phileFriendly New Member

    Joined:
    Jun 22, 2005
    25
    0
    0
    Location:
    WA
    I am doing my front speaker replacement today, and just got the driver door off. However, I'm unsure of which wires I should be hooking up to my crossover. I see a yellow and a black wire running to the woofer. I see a yellow, a black, a pink, and a purple running to the tweeter. What should be the input + and - for the crossover? What should I be doing with the leftover wires?

    thanks in advance!
     
  2. Bobv

    Bobv Junior Member

    Joined:
    Jun 14, 2005
    13
    0
    0
    Use the tweeter wires for the xover input as the 6" driver wires are looped from the tweeter plug. Dark wires are neg. and light colors pos. Looking at the back of the tweeter will tell you which is pos. the capacitor goes to the pos side.
     
  3. phileFriendly

    phileFriendly New Member

    Joined:
    Jun 22, 2005
    25
    0
    0
    Location:
    WA
    Thanks. Does that mean I should use the pink and purple wires as the input for the crossover, and the yellow and black wires at the tweeter (which also there are a pair of goign to the woofer) should be connected to the woofer output section of the crossover? So basically, the yellow and black wires are only going between the woofer and tweeter?

    thanks!
     
  4. silentak1

    silentak1 Since 2005

    Joined:
    Jul 1, 2005
    893
    28
    0
    Location:
    LA
    Vehicle:
    2010 Prius
    Model:
    III
  5. Bobv

    Bobv Junior Member

    Joined:
    Jun 14, 2005
    13
    0
    0
    I used the tweeter wires to supply input to the xover and ran new wire from the xover to each speaker.
     
  6. DanMan32

    DanMan32 Senior Member

    Joined:
    Aug 27, 2004
    3,799
    26
    0
    Location:
    Tampa Bay, FL
    You didn't specify if this was JBL or not. Doesn't sound like it is.

    Rear fullrange is yellow/black on the driver's side, Red and White on the passenger side.

    Pink and Purple run from the radio to the tweeter, then out of the tweeter to the fullrange in the driver door.

    On the JBL system, both the tweeter and the full range use pink and purple leads, but they are separate to the amp.
     
  7. phileFriendly

    phileFriendly New Member

    Joined:
    Jun 22, 2005
    25
    0
    0
    Location:
    WA
    Thanks for all the advice guys. Yes I do have the non-JBL version, and I was redoing the front speakers.

    I ended up plugging the pink and purple wires into the input of the crossover, then ran a couple new wires to the tweeter, and connected the yellow/black wires to the woofer output section of the crossover. It does appear that the yellow/black (on the drivers side) are merely running between the tweeter and woofer, so that worked great.

    On the passenger side, I had 2 sets of green/blue wires. I was able to differentiate between them because one set (the set running between the woofer and tweeter) had a gold dot marked every so often. The other pair had a greenish dot periodically (these dots appeared to be applied with a marker). So, I connected the green dot wires to the input section of the crossover, the gold dot to the woofer output, and new wires for the tweeter.

    It all seems to work great... except... I can hear a very faint humming noise even when the radio is turned off (but the car is on). This is most noticable from the tweeter, and is barely audible but definitely there. I can hear the hum on both sets of speakers... is this common? It is quiet enough that the noise could have been there before I set up the speakers and I probably wouldn't have noticed it, but of course I have to wonder if it was something I did to cause it. Ideas?

    Thanks!
     
  8. tmorrowus

    tmorrowus Member

    Joined:
    Dec 30, 2003
    514
    15
    2
    Noise from speakers is often a side effect of installing an aftermarket amp and incorrectly setting the gain, grounding problems, or signal isolation issues. Since you didn't mention installing an amp, I don't know what happenned in your case.