1. Attachments are working again! Check out this thread for more details and to report any other bugs.

2001 Prius codes 3233 and 4448

Discussion in 'Generation 1 Prius Discussion' started by critterz, Jun 3, 2011.

  1. critterz

    critterz New Member

    Joined:
    May 22, 2011
    14
    0
    7
    Location:
    California
    Vehicle:
    2001 Prius
    Model:
    N/A
    Hi all, My new to me 2001 Prius has a slowly flashing Airbag light. Reading this handy forum I found that by jumping two pins on the OBD port I could read the codes generated by the flashing lights. I did that, and have a 3233 and 4448. The car runs and drives fine, fluids are all good etc. Can the codes be cleared and see if they return? Any suggestions? Thanks. John
     
    #1 critterz, Jun 3, 2011
  2. vincent1449p

    vincent1449p Active Member

    Joined:
    May 24, 2004
    894
    331
    0
    Location:
    Singapore
    Vehicle:
    2012 Prius c
    Hi critterz,

    Those codes refer to the malfunction of the side airbag.

    32 (B1140) - Side airbag sensor assembly (RH) malfunction
    33 (B1141) - Side airbag sensor assembly (LH) malfunction
    44 (B0111) - Open in side squid (RH) circuit
    48 (B0116) - Open in side squid (LH) circuit

    Procedures to clear code
    (1) Connect the 2 service wires to terminals TC and AB of DLC3.
    (2) Turn the ignition switch to ON and wait for approx. 6 seconds.
    (3) Starting with the TC terminal, ground alternatively terminal TC and terminal AB twice each in cycles of 1.0 second. Make sure that the terminals are grounded. Ensure the terminal TC remains grounded.
    HINT:
    When alternatively grounding terminals TC and AB, release ground from one terminal and immediately ground the other terminal within an interval of 0.2 seconds.
    If DTCs are not cleared, repeat the above procedure until the codes are cleared.
    (4) Several seconds after doing the clearing procedure, the SRS warning light will brink in a 50 - msec. cycle to indicate the codes which have been cleared.
     

    Attached Files:

    #2 vincent1449p, Jun 4, 2011
    1 person likes this.
  3. critterz

    critterz New Member

    Joined:
    May 22, 2011
    14
    0
    7
    Location:
    California
    Vehicle:
    2001 Prius
    Model:
    N/A
    Thank you Vincent! This makes sense. My airbag module was replaced and my car does not have side airbags. I bet the module I got (ebay) was for a side airbag equipped car. Thanks for the help! John
     
    #3 critterz, Jun 4, 2011
  4. critterz

    critterz New Member

    Joined:
    May 22, 2011
    14
    0
    7
    Location:
    California
    Vehicle:
    2001 Prius
    Model:
    N/A
    Hi all, I'm back again. I switched back the original airbag module and get flashing code 24 and 31. I tried unsuccessfully to clear them. Any suggestions? Driving the heck out of it and LOVE it! Hit 100000 miles today. Took a picture! Thanks all.
     
    #4 critterz, Jun 9, 2011
  5. vincent1449p

    vincent1449p Active Member

    Joined:
    May 24, 2004
    894
    331
    0
    Location:
    Singapore
    Vehicle:
    2012 Prius c
    Hi John,

    I 've replied your PM.

    Vincent
     
    #5 vincent1449p, Jun 9, 2011
  6. seilerts

    seilerts Battery Curmudgeon

    Joined:
    Mar 7, 2010
    3,326
    1,512
    38
    Location:
    Santa Fe, NM
    Vehicle:
    2005 Prius
    31 is "airbag sensor assembly malfunction" and 24 is "half connection in airbag sensor assembly". As far as I know, the airbag computer must be reprogrammed after airbags have deployed.
     
    #6 seilerts, Jun 10, 2011
(You must log in or sign up to post here.)