1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Ham Radios

Discussion in 'Toyota Hybrids and EVs' started by Gadget 1004, Jun 2, 2012.

  1. Gadget 1004

    Gadget 1004 Junior Member

    Joined:
    Oct 27, 2010
    13
    1
    0
    Location:
    Mesquite, Texas
    Vehicle:
    Other Hybrid
    Model:
    N/A
    Hello everyone. I just purchased a 2012 Camry Hybrid XLE Red. I need to install my Kenwood 700a in the vehicle. Has anyone installed a ham radio in their Camry? Do you have any suggestion or pictures of the installion.
    Thanks,
    KC5TOO
     
    #1 Gadget 1004, Jun 2, 2012
  2. KK6PD

    KK6PD _ . _ . / _ _ . _

    Joined:
    Mar 24, 2008
    4,003
    944
    118
    Location:
    Los Angeles Foothills
    Vehicle:
    Other Hybrid
    Model:
    N/A
    While I don't have the HyCam yet, long story, It should be very easy to install a rig. Just make sure you follow good Amateur installation practices, such as running both Positive and Negative directly to the +12 battery, if running HF you are going to have to shield some components to eliminate QRM. If it's 2meter and above, no problems. Do some searching, there are quite a few Amateurs out here, H'mmmm wonder why?
    Post some pick when you get it done.
    I run a Yaesu FT-8800, Diamond K-400 mount and Black dual band whip!
    It works great!

    Bye the way, welcome to the group!!!
     
    #2 KK6PD, Jun 3, 2012
  3. Gadget 1004

    Gadget 1004 Junior Member

    Joined:
    Oct 27, 2010
    13
    1
    0
    Location:
    Mesquite, Texas
    Vehicle:
    Other Hybrid
    Model:
    N/A
    Thank for the welcome. I am moving from the Prius Chat because I sold my Prius and up graded to a Toyota Camry. We have chatted before on the Prius Chat about Ham Radios. Looking forward to reading about the Toyota Camry Hybrid's on the forum. Now I am trying to figure out how to add an avatar.
     
    #3 Gadget 1004, Jun 3, 2012
  4. Gadget 1004

    Gadget 1004 Junior Member

    Joined:
    Oct 27, 2010
    13
    1
    0
    Location:
    Mesquite, Texas
    Vehicle:
    Other Hybrid
    Model:
    N/A
    Here is my installation of my Ham Radio into my 2012 Camry XLE Hybrid.
    [​IMG]

    Antenna Installation
    [​IMG]

    [​IMG]

    [​IMG]

    Decided to mount the radio under the rear deck. Routing the cables were easy.
    [​IMG]

    Had to find a place to mount the control head, mike and speaker.
    [​IMG]

    [​IMG]

    Had to make a mount. No holes were drilled.
    [​IMG]

    [​IMG]
     
    #4 Gadget 1004, Jun 3, 2012
  5. KK6PD

    KK6PD _ . _ . / _ _ . _

    Joined:
    Mar 24, 2008
    4,003
    944
    118
    Location:
    Los Angeles Foothills
    Vehicle:
    Other Hybrid
    Model:
    N/A
    +1, A+
    Nice install!
    You did good!!! :)
     
    #5 KK6PD, Jun 3, 2012
  6. abq sfr

    abq sfr New Member

    Joined:
    Mar 28, 2007
    690
    3
    0
    Location:
    Albuquerque, NM
    Vehicle:
    2007 Prius
    I too traded in my Prius... only on a non-hybrid 2012 Camry SE. I've been scratching my head on where to put the control head and antenna, this gives me some great ideas, thanks and 73! KD5RHR
     
    #6 abq sfr, Jul 31, 2012
  7. x1sspic

    x1sspic New Member

    Joined:
    Oct 19, 2012
    1
    0
    0
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A
    Looks good, KC5TOO. I just bought a new Barcelona Red Camry V6 LE. I have a Kenwood radio I was thinking about installing, but want to do it RIGHT.

    How did you wire the +12V/ground? Did you run wire up to the battery (if so, where did you run through?), or is there already a feed into the trunk? Also (presuming you wired up to ignition sense), where is there access to ignition for ignition sense? Thanks for any tips,

    Scott / KC2JYG

     
    #7 x1sspic, Oct 19, 2012
  8. radioguy

    radioguy Junior Member

    Joined:
    Jul 25, 2005
    7
    0
    0
    I'm out of the Prius business, but did turn around and buy a 2020 Camry Hybrid. I'm installing a new Icom 208H VHF/UHF rig this summer, and I was looking for suggestions as to how to install it. Then I came across this thread and wow, what a really nice installation! Beautiful work and I've now got some ideas for my situation.
    I especially like the fact that I can install the guts of the transciever in the trunk and put the control head wherever I want (within reason). And, this will work out since I plan on using the 12V battery that's in the trunk to feed my Icom. My only head scratcher is what make of antenna to install. I see Gadget 1004's pictures (thanks for making these available for us) but can't tell what it is. Comet? Or something else? Thanks again for the pictures-they're very helpful!
     
    #8 radioguy, Jul 31, 2022
(You must log in or sign up to post here.)