1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Driver Side Window Off Track

Discussion in 'Generation 1 Prius Discussion' started by garywhite, Jan 12, 2010.

  1. garywhite

    garywhite Junior Member

    Joined:
    Jan 12, 2010
    25
    0
    0
    Location:
    Oakland, CA
    Vehicle:
    2001 Prius
    Model:
    N/A
    Yesterday as I was rolling down my window it came off the track/weatherstripping. I'm able to roll the window about half way up before the glass pinches at the very front next to the side mirror. The glass ends up wedged between the weatherstripping it should be in between and the outside of the door.

    Mechanically, everything is fine (as verified by a mechanic) I just need to get the glass back in the weatherstripping.

    I was able to remove the interior panel, but don't know how to get access to the interior of the door to try to re-align the glass.

    Any advice would be apprecaited
     
  2. garywhite

    garywhite Junior Member

    Joined:
    Jan 12, 2010
    25
    0
    0
    Location:
    Oakland, CA
    Vehicle:
    2001 Prius
    Model:
    N/A
    Hello All,

    I managed to get this one fixed on my own, but thought I would upload some pictures I took along the way for anyone else who runs into the same problem.

    The screws/plastic plugs to remove:
    [​IMG]

    Better look at where the plastic plug is:
    [​IMG]

    A look at the inside of the driver's side door panel:
    [​IMG]

    Driver's side door interior:
    [​IMG]

    A closeup of where my repair happened (story below):
    [​IMG]

    So as you'll see in the last photo, the white arrow is pointing to a white plastic piece. It's hard to see in the photo, but this is where the glass meets the lifting/lowering device. There *should* be a small bolt that is screwed in place there to keep the glass from separating from the lifter. At some point, this unthreaded itself in my car. I ended up popping this all the way off the lifting device and realigning the glass in the weatherstripping. I slowly raised the window and it fed completely into the weatherstripping. At which point I used a telescoping wand with a magnet on the end to fish out the missing bolt from my door. With the window back in track I just screwed that bolt back into place (you can see the threads in photo 5) and reassembled my door.

    The shop estimated this to be a 50-75 dollar job, but I would say anyone can do it. The only tools I used were a philips screwdriver and that telescoping magnet.

    Good luck!
     
  3. garywhite

    garywhite Junior Member

    Joined:
    Jan 12, 2010
    25
    0
    0
    Location:
    Oakland, CA
    Vehicle:
    2001 Prius
    Model:
    N/A
    Ahh, apparently I can't post any links until I have 5 posts... 2 to go.
     
  4. garywhite

    garywhite Junior Member

    Joined:
    Jan 12, 2010
    25
    0
    0
    Location:
    Oakland, CA
    Vehicle:
    2001 Prius
    Model:
    N/A
    A little time in Fred's House of Pancakes and I'm up to 5. I'll be editing the original post to include photos, lookout!
     
  5. adric22

    adric22 Ev and Hybrid Enthusiast

    Joined:
    Apr 6, 2009
    642
    144
    2
    Location:
    Fort Worth, TX
    Vehicle:
    2018 Chevy Volt
    Model:
    Plug-in Advanced
    I'm glad you posted these pictures, because I was thinking about taking my driver's side door apart to find the door-lock actuator. (as I mentioned in a different post, mine seems to be failing) and I was wondering where it is. However, looking at your pictures I still can't tell. Did you notice where that was?
     
  6. garywhite

    garywhite Junior Member

    Joined:
    Jan 12, 2010
    25
    0
    0
    Location:
    Oakland, CA
    Vehicle:
    2001 Prius
    Model:
    N/A
    You're going to have to excuse my ignorance - door lock actuator? Presumably this a mechanical piece after the physical switch? If you can point me in the right direction maybe it'll spark a memory.
     
  7. adric22

    adric22 Ev and Hybrid Enthusiast

    Joined:
    Apr 6, 2009
    642
    144
    2
    Location:
    Fort Worth, TX
    Vehicle:
    2018 Chevy Volt
    Model:
    Plug-in Advanced
    It is the "motor" if you will, that handles the locking and unlocking of the door when you use the keyless entry or the power-door-lock switch.
     
  8. EmptyLane

    EmptyLane Junior Member

    Joined:
    Jul 18, 2015
    2
    0
    0
    Location:
    Dallas
    Vehicle:
    2005 Prius
    Model:
    N/A
    Hi Gary,
    I just had this same trouble with my 2005 Prius drivers side window. It went down ok then went crooked on the way back up. I manhandled the window closed with the regulator up and keeping things from rattling. I got a $270 quote for repair that included a regulator replacement. Standard procedure to replace the regulator maybe?
    Based on yours and other posts, I think I might at least try to fix the bugger myself.
    Is there any way you could repost your pictures?
    Thanks!
     
  9. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    108,918
    49,500
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    try starting a conversation.
     
  10. Avi's Advanced Automotive

    Avi's Advanced Automotive Independent hybrid repair shop

    Joined:
    Jun 28, 2012
    775
    360
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2005 Prius
    Model:
    Three
    That post is five years old and for a Gen I, yours is a Gen II.

    Maybe try this:


    Avi
     
    bshef likes this.
  11. 3prongpaul

    3prongpaul Hybrid Shop Owner, worked on 100's of Prius's

    Joined:
    Jul 18, 2010
    954
    720
    1
    Location:
    Boulder Hybids, Boulder, CO
    Vehicle:
    2006 Prius
    Model:
    N/A
    Prius window regulators rarely fail.

    Usually problem is one of the two 10mm bolts come out that holds the glass to the regulator, or the plastic "clamps" at bottom of glass come off the glass. Check those first (after opening the door panel etc).

    By carefully running the window up/down it will line up with holes in the door to insert/tighten the bolts between regulator and glass "clamps".
     
    valde3 likes this.