1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Misfiring or something else?

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by Bens04Prius, May 17, 2017.

Page 4 of 4
  1. Bunce

    Bunce Active Member

    Joined:
    Jan 5, 2018
    321
    185
    0
    Location:
    Oregon
    Vehicle:
    2005 Prius
    Model:
    II
    So far so good. With about 300 miles done.


     
    #61 Bunce, Feb 1, 2018
  2. Bens04Prius

    Bens04Prius Junior Member

    Joined:
    May 8, 2017
    41
    3
    0
    Location:
    New Jersey
    Vehicle:
    2004 Prius
    Model:
    N/A
    The oil is actually wet... would piston ring or valve stem seal replacement qualify as an "engine overhaul?"
     
    #62 Bens04Prius, Feb 1, 2018
  3. valde3

    valde3 Senior Member

    Joined:
    Jun 28, 2014
    2,002
    745
    0
    Location:
    Finland
    Vehicle:
    2004 Prius
    Valve stem seals could be replaced without “engine overhaul” but normally they are done with it.

    Maybe wet fouled spark plug cap could be caused by some problem in the ignition system. Like bad spark plug, bad ignition coil, or wiring to it (or ecu).
     
    #63 valde3, Feb 1, 2018
  4. padroo

    padroo Senior Member

    Joined:
    Jan 11, 2008
    2,763
    2,250
    13
    Location:
    Chesterton, Indiana Another third world country.
    Vehicle:
    2016 Prius
    Model:
    Four
    I saw Mode 6 mentioned earlier in this post. There are actually 9 OBD II Modes and here is a list.

    OBD II modes are:

    *Mode 1: Real-time data, MIL, IM monitors.


    *Mode 2: Freeze frame.


    *Mode 3: Stored DTCs.


    *Mode 4: Clear/Reset DTCs and emissions-related diagnostic information.


    *Mode 5: O2 monitoring tests, supported.


    *Mode 6: Test results for continuously and noncontinuously monitored systems, supported.


    *Mode 7: Pending DTCs.


    *Mode 8: Request control of on-board-system, test or component (bidirectional controls).


    *Mode 9: Request VIN and other data.


    These are the nine areas some scan tool can read. A simple code reader will not read these.


     
    #64 padroo, Feb 1, 2018
    SFO likes this.
  5. Bens04Prius

    Bens04Prius Junior Member

    Joined:
    May 8, 2017
    41
    3
    0
    Location:
    New Jersey
    Vehicle:
    2004 Prius
    Model:
    N/A
    So for the recent few months car has been driving more or less fine, with no obvious misfires or any check engine lights at all - though I continue to hear the chirping like noise - it popped into my head that it might be the belt causing the noise so I wanted to rule that out & I got searching here on the forums.

    I have long been suspecting that this noise is only when the car is put into drive = when the engine connects to the transaxle.

    I decided to put it into a base idle and made a recording - basically the engine seems to be idling fine (for an engine this old) and noise pops up as soon as I put it into drive. Can someone explain any possibilities of this NOT being a transaxle issue? can it be that the engine only acts up under load = as soon as it connects to transaxle?

    Just to clarify it does NOT sound like this guys issue: Severe Knock/Rattle (maybe from transaxle?) | PriusChat
     
    #65 Bens04Prius, Apr 20, 2018
  6. Bens04Prius

    Bens04Prius Junior Member

    Joined:
    May 8, 2017
    41
    3
    0
    Location:
    New Jersey
    Vehicle:
    2004 Prius
    Model:
    N/A
    So I took the car to a mechanic that actually seemed to know what he's doing and he said it seems the water pump is failing - not leaking as far as he can tell, but water pump should be replaced. He said that the vibration & rumbling of engine may be something else, may be something with the motor winding that if it failed partially, it goes under load 2/3 of way, then slides of last third and repeat. Or its something else, he's not sure as he is not that familiar with hybrids.

    Indeed I do hear a similar component of sound on my car as in this video:
    but mine maybe has more of a squeak to it. I read somewhere that if bearing is bad it can cause some vibration that is detected by knock sensor and can cause rough idle... anyone have an experience like that? Recommendation is to try to take off belt and see if it vibration & rough idle goes away with belt off...
     
    #66 Bens04Prius, May 15, 2018
  7. padroo

    padroo Senior Member

    Joined:
    Jan 11, 2008
    2,763
    2,250
    13
    Location:
    Chesterton, Indiana Another third world country.
    Vehicle:
    2016 Prius
    Model:
    Four
    I was thinking the same thing, remove the belt and rotate it by had and see if it has any play in it. Run the car without the belt and check for the vibration. Don't run the car too long so you don't overheat it. What do you have to loose?
     
    #67 padroo, May 15, 2018
  8. Bens04Prius

    Bens04Prius Junior Member

    Joined:
    May 8, 2017
    41
    3
    0
    Location:
    New Jersey
    Vehicle:
    2004 Prius
    Model:
    N/A
    What do these codes tell me? Anything else I can do with a Techstream to explore some more possibilities?
    upload_2019-5-26_19-45-9.png
     
    #68 Bens04Prius, May 26, 2019
(You must log in or sign up to post here.)
Page 4 of 4