Will 86110-47230 work instead of 86110-47081 in 2005 Base Model?

The MFD will work if you rearrange the wires on the plug; I have done this MFD swap on my 2004 and all functions work..
I don't think the MFD would have anything to do with the bluetooth problem, but if you still need the pin reassignment, I'll post it.

 

If you have the pin reassignment, I could use it. Bought one from ebay and showed up the 47230 instead of the 47081.

Thanks

 

Following... Because I want the pin assignment too! Please

 

I followed this image I found from a 2008 Prius. Just moved yellow, green, brown, grey, and white with grey. The picture doesn't show the white with grey, but it goes in pin 11.

 

Can you tell me how you move the pins? Did you just yank it out and force the pin in appropriate slot?

 

I spent an hour trying to get the pins out. Usually very small screw driver will do the job, you can search on youtube how to re pin a wire harness, but i could not for the life of me get them out, so I cut and spliced and soldered. Not the best work I have ever done but it should out last the rest of this 14 year old car.

 

Alright thank you for your tip! Now I’m eager to upgrade my MFD on my 2005 Prius! Many people on Priuschat said it’s not possible... With a newer MFD I can gain better graphic and hopefully a backup camera with the help of this adapter. Rear View Camera Connection Cable to Toyota Prius Touring Lexus RX350, RX400h MFD GEN5 Multi-Displays

 

I made the change from 2004 base-->2006 w/camera. Here are the pin assignments from the wiring diagrams (Please use a meter to check your existing plug to be sure of the power wires.) You can find pin extractors on Amazon/eBay such as this: Car Wire Harness Terminal Extractor, but I still had one I couldn't get out and just spliced it.

	2004 Pin	Wire Color	Signal		2006 Pin	Wire Color	Signal
1	3	Brown	GND1		1	Brown	GND1
2	4	Black	TX1+ GTX+		4	Black	TX1+ GTX+
3	5	White	TX1- GTX-		5	White	TX1- GTX-
4	7	Pink	TC DL3		7	Pink	TC DL3
5	10	Black	IG+ 7.5A		10	Black	IG+ 7.5A
6	11	Gray	ACC+ 7.5A		2	Gray	ACC+ 7.5A
7	12	Yellow	B1+ 15A		3	Yellow	B1+ 15A
8	16	Red	PKB Brake Sw
9	17	Black	DR HSD1 - Body ECU		17	Black	DR HSD1 - Body ECU
10	18	Pink	TX2+ Radio		18	Pink	TX2+ Radio
11	19	White	TX2- Radio		19	White	TX2- Radio
12	25	Violet	SPD Combi		20	Violet	SPD Combi
13					21	Pink	REVERSE+ Relay
14
15					24 C	Shield	SLD Radio
16					25 C	Black	IVO+ Radio
17					26 C	White	IVO- Radio
18					27 C	Red	V+ Camera
19					28 C	Shield	V- Camera
20					29 C	Black	CA+ Camera
21					30 C	White	CGND Camera
22					31 C	White/Black	GND

 

To Re-pin, you need to raise the retainer on top of the plug (similar to this)

And then release the individual pins

I was able to use a small jeweler's screwdriver for the larger wires, but not the small ones.

 

Hi ITBland, Thank you for posting up this information. I also have a 2004 Base with a 86110-47080. Do you know if the 2006 MFD that you replaced yours with was a 86110-47230?

With your PIN assignemnts, I can see that the Brown, Gray, Yellow, and Violet need to be moved. I'm as bit confused with Jedimaster80's post with regards to a couple of different colors (yellow, green, brown, grey, and white with grey). My goal is just replace mine with a working unit and keep all the same functions as before.

 

Fond it there the harnesses are different on both upon further inspection so re-pinning won't work for me. Thanks anyways!

 

Are the Canada models different?
All you should need is the connector labeled M13 in the post above and move 4 of the pins around:

• 3 (Brown) moves to 1,
• 11 (Gray) moves to 2,
• 12 (Yellow) moves to 3, and
• 25 (Violet) moves to 20 (this one is tiny and hard to release!)

And, you can add a reverse camera (extra wires and connector needed)
(NOTE: The M14 connector is labeled "C" in my table, has the camera and Bluetooth wires)

 

I don't think Canadian models are different in this case. That Connector I don't have unfortunately. I'll have to try to go find one. Thank you!

 

Wow--incredible detail!

I'm just trying to replace a 2006 MFD with failed touch screen with an equivalent unit. The dealer quoted me $8,700 but was good enough to tell me I needed a 861104-47230c0. I just ordered a used 861104-47230 but have two questions.

What is the dif between 861104-47230c0 and 861104-47230?

Are there "lock code" issues?

Thanks.

 

Assuming you mean 86110-47230-C0, the “-C0” suffix means the plastic trim has a black finish. The part number may sometimes appear without the suffix, but as far as I know, it’s the same part—black is the only color.

I didn’t see anything in the Repair Manual, available by subscription to techinfo.toyota.com, about any reprogramming required when replacing the multi-display assembly.

 

I have a 2004 that had a bad screen. I found a 2004 with nav cheap at a Pick-N-Pull, bought the MFD and plugged it into my non-nav 2004 and it worked (no nav functions just extra buttons). I kept an eye out for a Prius with backup camera, found a non-nav 2006 in a Pick-N-Pull, got the MFD and camera, re-wired my 2004 plug as stated above, and the 2006 MFD was just plug-n-play in the 2004. The 2006 MFD has bluetooth (phone only), but my 2004 radio does not have the input for it, so no bluetooth (and no errors, it just does not show in the MFD options.)

 

@ITBland

How do I remove the small violet wire? I think I destroyed that plastic holding clip inside.

 

Never mind. I destroyed the plastic internal locking clip on that side for the violet wire. A hard yank and it finally came out. Red triangle is gone now that I moved the violet wire from #25 to #20

 

The original table above was missing the two illumination wires that must also be moved. Here is the corrected table: