1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Gen II cell reconditioning capacity cut-off question

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by mikethegeologist, Feb 9, 2019.

  1. mikethegeologist

    mikethegeologist Junior Member

    Joined:
    Feb 9, 2019
    2
    0
    0
    Location:
    Ohio, USA
    Vehicle:
    2006 Prius
    Model:
    N/A
    I've searched the forums pretty hard and have not found an answer to this question, forgive me if I missed it elsewhere.
    I'm reconditioning the traction battery in my 2006 Prius. I've already identified one cell as bad, and the reconditioning process is going pretty well, with one exception. My cell # 1 has given me "Capacity Cut-Off" messages twice, with two different chargers. Here is my set-up:

    I'm using 4 HTRC C240 Duo chargers (8 cells at a time) and I am doing 5 Discharge then Charge cycles. Charge is 5 A, Discharge is 1A and 6.4V cuttoff is set at 7500 ma, and the rest is set at 5 minutes. I took the cell off the charger and tested it with no load (8.36V), with one minute of 100 watts load (7.76V), and a final voltage of 8.28V five minutes after the load test.

    My question is, is there a problem with this cell, or is it just in good shape and hitting the full charge early?

    Thanks!
     
    #1 mikethegeologist, Feb 9, 2019
  2. 1ADAM12

    1ADAM12 Junior Member

    Joined:
    Mar 12, 2019
    2
    1
    0
    Location:
    San Antonio
    Vehicle:
    2005 Prius
    Model:
    Base
    Did you ever figure this out? I'm having the pretty much the same problem.
     
    #2 1ADAM12, Mar 12, 2019
  3. Wenjun Li

    Wenjun Li Junior Member

    Joined:
    Jun 1, 2020
    3
    0
    0
    Location:
    tauranga
    Vehicle:
    Other Hybrid
    Model:
    N/A
    Anyone?
     
    #3 Wenjun Li, Jul 21, 2020
    Last edited by a moderator: Jul 21, 2020
  4. TrillingThrows

    TrillingThrows New Member

    Joined:
    Mar 16, 2021
    17
    6
    0
    Location:
    California
    Vehicle:
    2011 Prius
    Model:
    II
    I believe the error means that one or more of your modules might have been overcharged and or discharged. This probably means that one or more of your modules have low capacity. When a module is at low capacity they tend to overcharge and discharge and a simple before and after reading would not pick up any issues because the voltage can bounce back quickly as soon as you take the load off. You need to determine the capacity of you modules , if there is a module/s whose capacity is too different from the average those are the ones that are giving you the problem. You can also look at the voltage UNDER load and compare it to when it is idle , any big differentials will also cause issues.
     
    #4 TrillingThrows, Mar 21, 2021
  5. Barry CLEMENTS

    Barry CLEMENTS Junior Member

    Joined:
    Feb 22, 2019
    52
    9
    0
    Location:
    92129
    Vehicle:
    2006 Prius
    Model:
    N/A
    Did you load test your cells using the C240? If so, how?
     
    #5 Barry CLEMENTS, Jan 2, 2022
  6. luisneto

    luisneto Junior Member

    Joined:
    Nov 21, 2018
    6
    2
    0
    Location:
    aveiro
    Vehicle:
    2005 Prius
    Model:
    N/A
    In this cases i do an discharge, and when it stop i can get the capacity
     
    #6 luisneto, Jun 3, 2022
(You must log in or sign up to post here.)