1. Attachments are working again! Check out this thread for more details and to report any other bugs.

LED Light bar installation

Discussion in 'Gen 2 Prius Audio and Electronics' started by ShaneBacon, Jul 24, 2018.

  1. ShaneBacon

    ShaneBacon Junior Member

    Joined:
    Aug 18, 2015
    22
    8
    2
    Location:
    Michigan
    Vehicle:
    2008 Prius
    Model:
    N/A
    After a run in with a deer, I thought of installing an LED light bar in the grill. I measured and I would need a 28in light bar to cover the whole front plastic piece of the grill. I'd have to cut a hole in the plastic grill piece for the light to come out appropriately of course. Would anyone advise against this for ventilation purposes? I live in a cooler climate and the car never has problems with temp...

    Here is the light bar I plan on installing:


    Wiring harness:


    I was also thinking about wiring it into the brights... I cannot seem to find the location of the brights relay however.

    Let me know what you think! And of course I'll post pictures when I'm done.
     
  2. SdzDesigns

    SdzDesigns New Member

    Joined:
    Dec 16, 2018
    7
    6
    0
    Location:
    Parma
    Vehicle:
    2005 Prius
    Model:
    II
    I am installing a 32" curved bar in the lower section where the foglights would go.
     
  3. oil_burner

    oil_burner Active Member

    Joined:
    Feb 26, 2017
    249
    126
    0
    Location:
    Canada
    Vehicle:
    2006 Prius
    I have a good 8" bar in my upper grille, I cut away a part of the plastic for it to fit. You want to have the LED bar at headlight level, too low and it doesn't do much. I wired mine into the hi beam's as well, I just ran a relay under the hood that tapped into the hi beam wire, it just takes the 12v signal for the relay, and the power for the bar is taken from the fuse box.

    I would recommend getting a smaller high quality bar vs a cheap 30" eBay chinese bar. The Chinese ones leak water, fog up inside, and don't throw light very far down the road, they flood tons of light just 20-30 feet out which is not useful for deer. Mine is a Baja designs and it throws light about 1/2 mile down the road.
     
  4. jjdd

    jjdd New Member

    Joined:
    Jan 16, 2019
    5
    7
    0
    Location:
    CA
    Vehicle:
    2007 Prius
    Model:
    Touring
    Can I ask which particular designs you purchased? I just purchased an 8" Rough Country. I wanted to see if you could help me with my install. I have the light up and running. My problem is my current switch is constantly on. Did you wire your so that you only have power with the ignition started? How did you relay it into your head lights as well? Hope that makes sense. Thanks!
     
  5. SdzDesigns

    SdzDesigns New Member

    Joined:
    Dec 16, 2018
    7
    6
    0
    Location:
    Parma
    Vehicle:
    2005 Prius
    Model:
    II
    My 32 bar from ebay works great.
     
  6. SdzDesigns

    SdzDesigns New Member

    Joined:
    Dec 16, 2018
    7
    6
    0
    Location:
    Parma
    Vehicle:
    2005 Prius
    Model:
    II
    This pics was before adjustment. It is plenty bright.
     

    Attached Files:

    DanGiant likes this.
  7. jjdd

    jjdd New Member

    Joined:
    Jan 16, 2019
    5
    7
    0
    Location:
    CA
    Vehicle:
    2007 Prius
    Model:
    Touring
    Did you remove your bumper to mount the bar?
     
  8. Tommy Leonard

    Tommy Leonard New Member

    Joined:
    Jul 16, 2024
    2
    0
    0
    Location:
    Orlando, Fla
    Vehicle:
    2016 Prius
    Model:
    Four Touring
    They make a fuse with a wire that fits into the high beam fuse slot so you can run your bar off your high beam. Not sure where to get it. JMO, those inexpensive light bars do not even come close to an LED light bar from Morimoto.