Swapping in a Gen 4 Prius' 2ZR Engine into the Prius v

I took the car for spin on the highway and the p0012 code came back. Looks like I have some reading/watching videos to do... Ok- found this video on the subject that I thought was pretty useful:

In it, he talks about the common problems and fixes:

1. Oil: is too old, is too low, or wrong type used. I had done an oil and filter change yesterday. I put in the 4.4 quarts of the 0W-20 synthetic (Mobile) like recommended in the manual. The oil level also looks correct on the dipstick.
2. Check the variable valve timing control coil (Toyota call it a Camshaft Timing Oil Control Valve). It's on the top, left (passenger side) of the engine. The harness is plugged in and all the way so I decided to swap it with the Gen 3...

Hmmm... I don't think that's supposed to be bent like that. The one off of the Gen3 is straight.

I believe that something heavy was placed on top of the engine because when prepping the engine I noticed the #2 coil had a cracked and bent connector body compared to the rest of the coils.

I figured that I'd just run the engine later on and see if I got any codes, then replace it, but I didn't realize that something else (VVT cam sensor) was also f'd as well. On a side note, I also had to replace the crank position sensor on the back side of the engine, b/c it was also just a wee bit f'd.


So, I popped in the VVT Sensor, fired up the car in maintenance mode, and I cleared the codes. After a bit of rough idling, the idling smoothed out and the p0012 code didn't seem come back! Yay. I then took the car for a spin on the highway...

Yep, P0012 is solved, but I ended up getting P0403 on this test drive... ugh. So close!

Update: Damn! another connector not plugged all the way in!

 

Another test drive later and no codes! Amaizing! I'll check in later to post anything noteworthy.

This thread and @Ragingfit 's videos have been a godsend! I also got some bracket inspiration from this UK guy's video

.

Speaking of brackets, here are a few that I created for the engine. All of them were made using aluminum angle & plate from a local scrap metal place (it's SUPER inexpensive to get all types of metal there). I used a few woodworking tools, a hack saw, desktop drill press, and table saw to cut, shape and bend the parts into existence.

• Below the water outlet to support the harness:
  
• On the front, Driver's side, top corner to replace the now missing 3rd mounting point for the air box and add another place to attach the vapor hose:
  
  
• on the top, rear, driver's side of the engine (crossing over the vapor pipe) to add a mounting spot for the harness side of the connector to the engine coolant temperature sensor that is tied into the bleed port:
  
  (sorry for the not so great pic- didn't feel like taking off the whipper assembly just to get another pic)

And now for the obligatory finished engine-installed shot:

Redoing the headlights is probably going to be my next project.

 

Congrats! This is so awesome

 

The engine I received does have this coolant hose around the back of the engine block. This hose connects to the hose from the egr cooler. They come from/go to? the water outlet with temp sensor at the block. There is a flow control valve and additional temperature sensor which I believe controls that valve (gray body). It appears the valve has a minimum flow when unpowered and when powered opens for maximum flow. I've ordered a water outlet with regular hose connection instead of flange connection for that control valve, then I can just connect the hose directly to the water outlet.
The part number is 36133-37100(i think), saw it on a random yt video from a guy in the UK. He ran into overheating issues which was resolved by removing this valve. Assuming due to lowered flow because it is a normally closed(min flow) valve.

 

Yup- that's the same UK guy's video that I posted above where I got inspired to create my brackets. He just covers a bunch of the changes that he did for his Prius in the vid. Good info in a relatively short video.

Update on my engine swap- 110 miles down and no issues, no check lights. The exhaust smells a little rich, but I'm assuming the ECM will eventually adjust it's parameters to the new engine (let me know if otherwise). I haven't really noticed any increase in power or fuel economy yet, but it does just drive like a Prius should.

Question for you all- what did everyone do with their old engine?

 

I was the only Prius owner on earth to take a perfectly good 100k mile engine out that didn't burn oil or have HG problems and install a Gen 4. I sold mine to a customer of the shop for a song, because he was looking for a used good condition engine and I was looking to upgrade.

 

Are you mass producing the prototype coolant hose yet? Great Idea.

 

Engine swap update:

I got everything hooked back up and filled. I put all the electrical connections on except the ignition coils per how ragingfit's did it in his videos.

At first sounded a little rough, then smoothed out, then I shut off. Guessing this was the oil getting distributed?

Then plugged the ignition coils in and started it up. Got error codes for each cylinder ignition coil, P0351, P0352, P0353 and P0354. obd2 app lists it as primary/secondary circuit malfunction. Cleared the codes and just shows up as archived with permanent status.

When I started it, it sounded good but with what seemed to be a little whining noise. After half a minute or so, it started to surge at a little higher rpm. So, I just shut if off. When shutting off, it makes a slight pressure like hiss noise as if the pressure of something was being released/reduced as it shut off.

I did use the gen4 vacuum switch, but wasn't thinking that would matter.

Here is a link trying to catch the whining sound and surge. Any ideas greatly appreciated!