2010 Prius NO CODE--Won't READY!

Discussion in 'Gen 3 Prius Care, Maintenance & Troubleshooting' started by Jonesy23, Jun 28, 2026 at 10:17 AM.

  1. Jonesy23

    Jonesy23 New Member

    Joined:
    Yesterday
    1
    0
    0
    Location:
    VA
    Vehicle:
    2010 Prius
    Model:
    Three
    my 2010 Prius started to lag on the highway. I quickly pulled over and tried to start it again and it would not go into ready. I bought a new 12V from Toyota it still won't go into READY. Odd things is there are NO CODES and NO TRIANGLE just the "Christmas Lights" on the dashboard. It is saying Shift to P to start and I checked the brake lights and they are fine. I checked under the shifter by pulling up the cover and all wires are connected. It's getting worse because the hybrid battery is dying as it's not being DRIVEN. It did say shift to P low traction battery but I don't know if that is because the hybrid battery is dying slowly which I may have to replace BUT I need to get to the origianal problem b/c if I gat a new hybrid battery and it still won't start this will not be good. Also, changed the inverter water pump and added gas to the car. I hear clicking in the back of the car near the 12 volt but it won't turn over. I tricked charged and tested 12 volt was nice and strong again after all this trouble shooting and still won't go into ready. I have the Dr. Prius app and it reads codes on my other prius so it's not me...this car is not giving me any codes not even a check hybrid system code only pops up once I disconnect the orange plug but when I put it back it no check hybrid system code.....I am so lost with this one. Please help. Thank you.
     
    #1 Jonesy23, Jun 28, 2026 at 10:17 AM
  2. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,928
    8,637
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    If your car died while driving, you either ran out of gas or your inverter has likely failed. There should be codes if you have a Prius capable code reader
     
    #2 JC91006, Jun 28, 2026 at 10:04 PM
  3. rjparker

    rjparker Tu Humilde Sirviente

    Joined:
    Jun 6, 2008
    10,911
    6,850
    7
    Location:
    Texas Hill Country
    Vehicle:
    2012 Prius v wagon
    Model:
    Three
    Dr Prius won't read all the codes.

    There should be codes if it suddenly stopped but we really don't know that because you said it was lagging.

    What "gear" does the display show?

    Do you do the coast in Neutral trick when you are driving? If it was in Neutral the hv battery can't charge.

    Have you been clearing codes by disconnecting the 12v battery?

    Are you sure you swung the hv disconnect in then pushed it sideways?

    An inverter fail can be sudden. An over temperature can cause a lower power limp mode. These will code.
     
    #3 rjparker, Jun 28, 2026 at 10:29 PM
    Last edited: Jun 28, 2026 at 10:34 PM
    Brian1954 likes this.
  4. Brian1954

    Brian1954 Senior Member

    Joined:
    Jan 31, 2021
    2,621
    1,037
    0
    Location:
    South Central PA, USA
    Vehicle:
    2011 Prius
    Model:
    III
    Use the Dr Prius app and look at the voltage of the battery at the top left side of the data page. Please post the voltage of the battery, and we will go from there.

    I would ask you to post a screenshot of the data, but you can not add file attachments or links into your posts until you have reached 5 posts. It is standard for new members to be moderated. That is why your posts are delayed.
     
    #4 Brian1954, Jun 28, 2026 at 10:37 PM
(You must log in or sign up to post here.)