1. Attachments are working again! Check out this thread for more details and to report any other bugs.

License plate scratching paint

Discussion in 'Gen 2 Prius Main Forum' started by jamesbugman, Jun 21, 2007.

  1. jamesbugman

    jamesbugman New Member

    Joined:
    May 29, 2007
    5
    0
    0
    I got home last night and found my new license late in the mailbox. I pulled the dealer frame and the temp plate off and found that the plate frame had blemished the paint on the hatch, it should buff out OK, but has anyone found a way to prevent the plate from scratching?
    I am thinking about getting the rubber stick-on dots or the felt pads, or should I just sand/buff the rough edges and install the plate as is? The dealer frame will NOT go back on, I even had them remove the logo from the hatch.

    Thanks
    James

    Have had the car for less than 4 weeks, averaging 45MPG. Beats the heck out of the ~20MPG that I got in my Deville, just hard to get use to the fact that this car is 3 feet shorter.
     
    #1 jamesbugman, Jun 21, 2007
  2. Presto

    Presto Has his homepage set to PC

    Joined:
    Mar 27, 2005
    1,326
    24
    0
    Location:
    Vancouver, BC
    Vehicle:
    2005 Prius
    I put sound deadening material on the back of the plate. It helps with the scratches. The main purpose was to stop the plate from rattling when the bass hits, but scratch prevention is a nice side effect :)
     
    #2 Presto, Jun 21, 2007
  3. thejdj

    thejdj Member

    Joined:
    Apr 9, 2007
    9
    1
    0
    Location:
    San Diego, CA
    Vehicle:
    2007 Prius
    I used a couple pieces of foam tape attached to the back of the plate.

    My first thought was to get a couple of stick-on rubber 'feet' to apply to the round indents of the hatch, but I already had the foam tape.
     
    #3 thejdj, Jun 21, 2007
  4. ServoScanMan

    ServoScanMan Member

    Joined:
    Apr 26, 2006
    262
    2
    0
    Location:
    Lorena, TX
    Vehicle:
    2006 Prius
    <div class='quotetop'>QUOTE(jamesbugman @ Jun 21 2007, 01:06 PM) [snapback]465853[/snapback]</div>
    I just had some stick-on felt pads I put on the back of the plate. Works for me.
     
    #4 ServoScanMan, Jun 21, 2007
  5. Tom_06

    Tom_06 Active Member

    Joined:
    Jan 10, 2006
    609
    141
    0
    Location:
    Newark, Delaware, USA
    Vehicle:
    2017 Prius Prime
    Model:
    Prime Advanced
    <div class='quotetop'>QUOTE(TheJDJ @ Jun 21 2007, 03:25 PM) [snapback]465933[/snapback]</div>
    I used the rubber feet (stick-on, about 1/4" in diameter and only 1/16" high), but on the back of the plate lined up to go in the indents. I think these are sold as cupboard door bumpers.

    - Tom
     
    #5 Tom_06, Jun 21, 2007
  6. jamesbugman

    jamesbugman New Member

    Joined:
    May 29, 2007
    5
    0
    0
    Thanks for the ideas. Looks like I'm not the only one to see this as an issue.

    James
     
    #6 jamesbugman, Jun 21, 2007
  7. David Beale

    David Beale Senior Member

    Joined:
    Jul 24, 2006
    5,963
    1,981
    0
    Location:
    Edmonton Alberta
    Vehicle:
    2012 Prius
    I used electronics "continuous grommet", a black plastic "U" shaped product, and used black silicone to glue it around the edge of the plate.
     
    #7 David Beale, Jun 21, 2007
  8. richard schumacher

    richard schumacher shortbus driver

    Joined:
    Mar 27, 2004
    7,663
    1,038
    0
    Location:
    United States
    Vehicle:
    2004 Prius
    Model:
    N/A
    Closed cell foam tape or gasket material *on the car*. If you apply it to the plate, dirt gets between the foam and the paint and the car gets scratched anyway.
     
    #8 richard schumacher, Jun 26, 2007
(You must log in or sign up to post here.)