1. Attachments are working again! Check out this thread for more details and to report any other bugs.

is there an easy way to lift the prius to rotate tires

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by ski.dive, Sep 19, 2011.

  1. ski.dive

    ski.dive Active Member

    Joined:
    Jun 11, 2008
    863
    223
    0
    Location:
    Hutchinson Island,FL. Mt. Snow,VT
    Vehicle:
    2008 Prius
    how do i jack up the prius on one side to remove both the front and rear tire at the same time so i can put the front tires in the rear?
     
  2. rogerv

    rogerv Senior Member

    Joined:
    Dec 10, 2008
    1,639
    317
    14
    Location:
    Simi Valley, California
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    I use a hydraulic floor jack at each of the two jacking points on a side, having slightly loosened the lugnuts first. Raise each jack far enough to remove the tire, make the switch, then snug the nuts down before lowering the car at both ends. Finally, use a torque wrench on all lugnuts. The floor jacks cost about $20 each on sale at auto supply stores.
     
  3. fgoodyear

    fgoodyear New Member

    Joined:
    Aug 28, 2007
    187
    11
    0
    Location:
    Tillson, New York
    Vehicle:
    2007 Prius
    I jack up the front, set a jack stand under the front subframe connection point to the rear of the wheel on whichever side I am working on. Then jack up the rear and do the same. Take the tires off and swap them.
     
  4. AllenZ

    AllenZ Active Member

    Joined:
    Jul 9, 2010
    640
    63
    0
    Location:
    Chicago
    Vehicle:
    2010 Prius
    Model:
    Four
    What's the torque should be?
     
  5. 2009Prius

    2009Prius A Wimpy DIYer

    Joined:
    Mar 25, 2009
    2,705
    509
    63
    Location:
    USA
    Vehicle:
    2009 Prius
    Here is a good picture to describe what I do:
    [​IMG]
    except I put the jack a little bit further back than in the picture, under the welded "cross".

    Torque is 76 ft.-lb. Good luck! :)
     
  6. qbee42

    qbee42 My other car is a boat

    Joined:
    Mar 2, 2006
    18,058
    3,073
    7
    Location:
    Northern Michigan
    Vehicle:
    2006 Prius
  7. Mark57

    Mark57 2021 Tesla Model 3 LR AWD

    Joined:
    Aug 14, 2009
    2,945
    2,735
    0
    Location:
    OK
    Vehicle:
    Other Electric Vehicle
    Model:
    N/A
    +1
     
  8. seilerts

    seilerts Battery Curmudgeon

    Joined:
    Mar 7, 2010
    3,326
    1,512
    38
    Location:
    Santa Fe, NM
    Vehicle:
    2005 Prius
    A lift is helpful.
    [​IMG]
     
  9. uart

    uart Senior Member

    Joined:
    Sep 7, 2009
    4,215
    1,200
    0
    Location:
    Australia
    Vehicle:
    2005 Prius
    How many of you guys cross rotate (LF to RR, RF to LR, LR to LF, RR to RF) as opposed to just doing a straight exchange of front and back?

    I know that if you've got tires with an asymmetric tread design then you have no choice, but otherwise what's your preference?
     
  10. Patrick Wong

    Patrick Wong DIY Enthusiast

    Joined:
    Mar 8, 2008
    18,198
    6,461
    0
    Location:
    Green Valley, AZ
    Vehicle:
    2015 Prius
    Model:
    Two
    I will cross-rotate if I find that one rear tire is wearing faster than the other.

    If that is not required and I am just swapping front to rear and vice-versa, then I will raise up the car in a manner similar to the photo provided by 2009Prius except I will use a 2 ft length of 2x4 lumber in the jack saddle to spread the load, and will place the jack at the outer rail, somewhat forward of center since the car's center of gravity is somewhat forward due to the powertrain weight.
     
  11. fuzzy1

    fuzzy1 Senior Member

    Joined:
    Feb 26, 2009
    17,038
    10,012
    90
    Location:
    Western Washington
    Vehicle:
    Other Hybrid
    Model:
    N/A
    If you lack a separate floor jack, do you another car in the household from which to borrow a second jack?

    I noticed that lifting two corners simultaneously reduces the load (per jack), making the cranking easier.
     
  12. Patrick Wong

    Patrick Wong DIY Enthusiast

    Joined:
    Mar 8, 2008
    18,198
    6,461
    0
    Location:
    Green Valley, AZ
    Vehicle:
    2015 Prius
    Model:
    Two
    The typical scissors jack is not very stable because the jack base is so small, and if you raise up two corners of the car with two scissors jacks then the car can easily topple. I would advise that you firmly set the parking brake and exercise extreme caution if you must employ that practice.
     
  13. fuzzy1

    fuzzy1 Senior Member

    Joined:
    Feb 26, 2009
    17,038
    10,012
    90
    Location:
    Western Washington
    Vehicle:
    Other Hybrid
    Model:
    N/A
    ^^ I always set wheel chocks on the other side when jacking up the car, even a single corner. And put some 4x6 blocks next to the jack points so the car won't fall all the way to the ground if the jack fails.

    Witnessing someone else's car fall, due to carelessness with a jack, is something that is remembered for a very long time.
     
  14. uart

    uart Senior Member

    Joined:
    Sep 7, 2009
    4,215
    1,200
    0
    Location:
    Australia
    Vehicle:
    2005 Prius
    I've just got a fairly small floor jack and a pair of pin adjustable car-stands. To cross rotate I jack each of the front wheels separately and place a stand at the normal jack lift points. So that gets both front wheels off the ground, where they stay throughout the rotation.

    I take off the two front wheels and place them at the ready next to each of the (opposite) rear wheels. Then the real wheels I just lift/change one at a time using only the floor jack. Obviously I don't get under the car or put myself in the way of any danger while the rear corner is supported only by a jack.
     
  15. fgoodyear

    fgoodyear New Member

    Joined:
    Aug 28, 2007
    187
    11
    0
    Location:
    Tillson, New York
    Vehicle:
    2007 Prius
    I was always told not to cross rotate radial tires. I always rotate just front and rear on same side. I was told it would screw up the wear pattern
     
  16. 2009Prius

    2009Prius A Wimpy DIYer

    Joined:
    Mar 25, 2009
    2,705
    509
    63
    Location:
    USA
    Vehicle:
    2009 Prius
    Here is what I do: (following Patrick's advice)

    Jack under the square rail weld:
    [​IMG]

    Jack stands under the Toyota jack points:
    [​IMG]

    [​IMG]

    And I stick my home made wood ramp under the car for extra safety if I crawl down there:
    [​IMG]
     
    blaisep and George Glass like this.
  17. fuzzy1

    fuzzy1 Senior Member

    Joined:
    Feb 26, 2009
    17,038
    10,012
    90
    Location:
    Western Washington
    Vehicle:
    Other Hybrid
    Model:
    N/A
    I heard the same thing in the early days of radials.

    But years later, reading the warranty booklet for a set of radials on my car, I discovered that cross rotation was acceptable for that particular model. Since then, only one set, marked as unidirectional, has not allowed that pattern.
     
  18. ahmeow

    ahmeow Prius Lover

    Joined:
    Nov 11, 2010
    366
    70
    0
    Location:
    North CA
    Vehicle:
    2011 Prius
    Model:
    Three

    Wow, very nice set of tailor made blocks. Strong and firm,the under frame is vell protected. Zero scratch or hurt. Nice,:p
     
  19. Old Still Running

    Old Still Running New Member

    Joined:
    Mar 18, 2015
    15
    2
    0
    Location:
    Santa Barbara, CA
    Vehicle:
    2007 Prius
    Model:
    N/A
    Is this the right place to jack for the front of a 2007 Prius?

    SC1.JPG

    FC2.JPG

    FC5.JPG
     
    #19 Old Still Running, Mar 22, 2015
    Last edited: Mar 22, 2015