1. Attachments are working again! Check out this thread for more details and to report any other bugs.

How to block your grill

Discussion in 'Gen 2 Prius Accessories & Modifications' started by acausedelle, Jan 18, 2013.

  1. acausedelle

    acausedelle Hypermiling Through Campus

    Joined:
    Jan 18, 2013
    14
    4
    0
    Location:
    Green Lake, Wisconsin
    Vehicle:
    2005 Prius
    Model:
    N/A
    Hey guys, I've been lurking on this site a lot, and I've come across a lot of cool modifications. This one seems to be the most relevant to where I live, and I want to go through with blocking my grill for the remainder of the winter, since I just bought my prius and am averaging 44 mpg, and I want to get better gas mileage.

    I'm probably going to use the pipe insulation, because it seems like the easiest form of doing it. People on here have asked this question many times, but I don't know the size of the pipe insulation to get. I was looking at this thread:

    Please explain HOW to block the grill | PriusChat

    But it's on a generation 3 prius. Is the sizing any different for the generation 2 prius? I'm going to block the upper grill and about half of the bottom grill since I don't have a scangauge (although I may buy one), and then take it out when spring rolls around. What's the best way to block half of it? Would blocking half of it be the top half? The passenger side? If anyone could help me, it would be appreciated!
     
  2. PriusGuy32

    PriusGuy32 Prius Driver Extraordinaire

    Joined:
    Sep 10, 2012
    1,411
    506
    0
    Location:
    Harrison Township, Michigan
    Vehicle:
    2015 Prius
    Model:
    Four
    I used the 3/8" pipe insulation, bought it from ACO for $1.19 for a 6 foot or so section.

    I halfed the pipe insulation. Then I stuck those in the grille.

    On my own preference, I left the drivers side of the grill open about 6" just go get some air in there. You dont have to do this, though. Some leave it completely blocked.

    Once you get the pipe insulation and cut it, you'll see exactly 2 ways it can fit. I took the half piece and folded it, then wedged it between the slats. Some dont fold it and just push it in the slat.
     
  3. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    107,571
    48,862
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    i used 1/2" on my gen II. cut it to length and slid the split over the horizontzl fin, 1/2 above and 1/2 below. also have to make verticle slices for the verticle fins.
     
    Daves09prius likes this.
  4. F8L

    F8L Protecting Habitat & AG Lands

    Joined:
    Aug 14, 2006
    19,011
    4,080
    50
    Location:
    Grass Valley, CA.
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A
    I used the same size as biscotti but I squeezed 1 whole piece into each slot.

    image.jpg
     
    bisco likes this.
  5. acausedelle

    acausedelle Hypermiling Through Campus

    Joined:
    Jan 18, 2013
    14
    4
    0
    Location:
    Green Lake, Wisconsin
    Vehicle:
    2005 Prius
    Model:
    N/A
    Thanks guys, I cut the tubing into 6 inch pieces and put it in there. I tested it out around town using pulse and glide (even though I'm very new to it), and averaged ~60 mpg. Very impressed since it's winter. My design could use some work and I may redo it. Thanks for your help guys!
     
    Daves09prius likes this.
  6. PriusGuy32

    PriusGuy32 Prius Driver Extraordinaire

    Joined:
    Sep 10, 2012
    1,411
    506
    0
    Location:
    Harrison Township, Michigan
    Vehicle:
    2015 Prius
    Model:
    Four
    Cool! It does make a big difference, I noticed right away with my mpg's. The only problem I had was if I go on a highway trip longer than 1 hour in duration, my ICE was getting too hot (204f) with the lower grille 90% blocked and the top 100% - even though I was leaving the drivers side of the grill unblocked 6". I took one whole piece out of the middle of the lower grille to allow for more air to pass through the radiator and as soon as I did my ICE temps dropped to 185f.

    Oh, nobody else has mentioned it yet but a Scangauge II or the Torque app on your smart phone coupled with a bluetooth OBD2 connector are GREAT ways to monitor your Prius and to squeeze the most mpgs out of it.
     
    ProZach likes this.
  7. Daves09prius

    Daves09prius Active Member

    Joined:
    Nov 20, 2010
    680
    161
    0
    Location:
    Gettysburg, PA
    Vehicle:
    2009 Prius
    Model:
    One
    When you are grille blocking how hot do you have your heat running? I usually set my temperature to 76 to 78 to pull some heat out of the ICE.
     
  8. PriusGuy32

    PriusGuy32 Prius Driver Extraordinaire

    Joined:
    Sep 10, 2012
    1,411
    506
    0
    Location:
    Harrison Township, Michigan
    Vehicle:
    2015 Prius
    Model:
    Four
    I generally put my heat on "AUTO" and turn the A/C off. When the car is fully warmed up I set the heat to like 70-71-72 usually.
     
  9. Daves09prius

    Daves09prius Active Member

    Joined:
    Nov 20, 2010
    680
    161
    0
    Location:
    Gettysburg, PA
    Vehicle:
    2009 Prius
    Model:
    One
    I'm just thinking if you're worried about grille blocking and the ICE overheating, you can turn your heat up inside the cabin to pull some of the excess heat out of the ICE. Remember there is essentially two radiators in the car, one is at the front of the engine compartment used for engine cooling, the second one is smaller and used for heating the air going to the cabin. That’s why when a car begins to overheat you can cool the engine down by turning the heat on full blast.

    I have a long commute going to work so I run my heat continuously at 76 degrees or higher when driving those long distances. It's nice to have heat during the super cold winter mornings.