1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Guide: Replacing Stock Horn with Hella Supertone for Prime

Discussion in 'Prime Accessories and Modifications' started by Mavi, Dec 13, 2019.

  1. Mavi

    Mavi Active Member

    Joined:
    Oct 12, 2015
    484
    282
    0
    Location:
    San Diego,ca
    Vehicle:
    2020 Prius Prime
    Model:
    XLE
    So I replaced the stock horns on the Prius prime with Hella supertones. I've also done dualtones before and they're close enough to me sound wise. Both are an improvement I just went with the supertones since I got a new set for $13.

    Step 1: Pop hood, remove the 6 clips with a flat head screwdriver or plastic trim remove. Then pull off the plastic engine cover.

    Step 2: disconnect the connectors from both left and right horns.

    Step 3: use 12mm socket to remove the lower bolt from the horn harness. Do on both, stock horns will now come out.

    Step 4. Make a ground strap. I used a spare copper electrical wire, but any copper wire include speaker wire will work . I crimped it using home depot electrical connectors for the rest.

    Step 5: Use a screw driver or sand paper to sand under the intake box screw. This is where ground wire will bolt to .

    Step 6 bolt in the two new horns using existing screws.

    Step 7: Either of the two spade connection can be a ground of positive doesn't matter which. Plug the ground strap to one. And to the other horn as well.

    Step 8: now plug in the original positive spade you pulled from the stock horns earlier to the other.

    Step 9: test the horns. If all is well put the engine cover and clips back and close up.
     

    Attached Files:

    Cellboy likes this.
  2. Salamander_King

    Salamander_King Senior Member

    Joined:
    Nov 8, 2015
    10,958
    8,836
    0
    Location:
    New England
    Vehicle:
    Other Hybrid
    Model:
    N/A
  3. Mavi

    Mavi Active Member

    Joined:
    Oct 12, 2015
    484
    282
    0
    Location:
    San Diego,ca
    Vehicle:
    2020 Prius Prime
    Model:
    XLE
    vvillovv and Salamander_King like this.
  4. Goat herder

    Goat herder Junior Member

    Joined:
    Nov 21, 2013
    7
    6
    0
    Vehicle:
    2012 Prius c
    Model:
    Two
    GREAT set of photos, and a clean upgrade of the
    Meep sounding horn.

    A month ago It was early morning I was waiting for a railway train to cross a state Hwy. Several semi trucks were heading back to the rock quarry they were using their train horns to honk at the train. Taking advantage of the " It was not me defense of violation of city posted ordinance "
     
  5. route246

    route246 Member

    Joined:
    Jun 18, 2007
    95
    49
    0
    Location:
    SF Bay Area
    Vehicle:
    2020 Prius Prime
    Model:
    Limited
    Thank you for posting this. I installed some Hella Sharptone horns today and it was very easy compared to my 2014 Prius.
     
    Mavi likes this.
  6. rdgrimes

    rdgrimes Senior Member

    Joined:
    Jun 7, 2013
    1,740
    444
    4
    Location:
    New Mexico, USA
    Vehicle:
    2018 Prius Prime
    Model:
    N/A
    Does someone have the part number for the absurd plastic push-pins holding the radiator cowl in place? A couple of mine are broken and I want to have replacements in hand when I do the horns.
     
  7. vvillovv

    vvillovv Senior Member

    Joined:
    Mar 19, 2013
    3,492
    1,231
    1
    Location:
    NY
    Vehicle:
    2017 Prius Prime
    Model:
    Prime Plus
  8. rdgrimes

    rdgrimes Senior Member

    Joined:
    Jun 7, 2013
    1,740
    444
    4
    Location:
    New Mexico, USA
    Vehicle:
    2018 Prius Prime
    Model:
    N/A
    I found "90467-06133-C0" in another thread here and ordered some off eBay, we'll see. There may be different part numbers for the same item depending on which model its used in.
     
  9. rdgrimes

    rdgrimes Senior Member

    Joined:
    Jun 7, 2013
    1,740
    444
    4
    Location:
    New Mexico, USA
    Vehicle:
    2018 Prius Prime
    Model:
    N/A
    BTW, these Hella horns with the Toyota connector are an exact fit. They come in LH and RH configurations and if you orient them correctly the existing connectors line up perfectly. They ground through the bracket so there's no messing with a ground wire.

    FWIW, the 90467-06133-C0 push pins are too small for the cowl. Trying 90467-07217 next
     
  10. Mavi

    Mavi Active Member

    Joined:
    Oct 12, 2015
    484
    282
    0
    Location:
    San Diego,ca
    Vehicle:
    2020 Prius Prime
    Model:
    XLE
    Awesome! thanks!
     
  11. rdgrimes

    rdgrimes Senior Member

    Joined:
    Jun 7, 2013
    1,740
    444
    4
    Location:
    New Mexico, USA
    Vehicle:
    2018 Prius Prime
    Model:
    N/A
    Following up, the 90467-07217 push pins appear to be an exact replacement, or at least close enough.
     
    Mavi likes this.
  12. chickenhawk

    chickenhawk Member

    Joined:
    Sep 13, 2011
    261
    95
    8
    Location:
    CA
    Vehicle:
    2021 Prius Prime
    Model:
    XLE
    These are on sale for $20 on Amazon, got a pair for my car.:cool:
    [​IMG]
     
  13. chickenhawk

    chickenhawk Member

    Joined:
    Sep 13, 2011
    261
    95
    8
    Location:
    CA
    Vehicle:
    2021 Prius Prime
    Model:
    XLE
    I put these Hella horns in and it really wasn't that much louder than the stock horno_O What is the purpose of the relay ? I just plug the harness on one side and the other pin I hooked to ground. I then honked my Highlander horn that was alot louder then this. Wth? So I'm boxing these and sending them back.

    I might try these out. Otherwise I will just get the OEM Highlander horns.

    [​IMG]


    Here are part numbers for the Highlander horns:
    upload_2021-4-22_6-12-1.png 865100E040 and 865200E020
     
  14. chickenhawk

    chickenhawk Member

    Joined:
    Sep 13, 2011
    261
    95
    8
    Location:
    CA
    Vehicle:
    2021 Prius Prime
    Model:
    XLE
    For those wondering #4 on the pic is the one that makes the hybrid sound in the Hybrids :cautious::whistle:

    upload_2021-4-22_6-17-6.png

    SPEAKER ASSEMBLY, VEHICLE APPROACHING
    [​IMG]
    Part Number: 8657048031
     
  15. chickenhawk

    chickenhawk Member

    Joined:
    Sep 13, 2011
    261
    95
    8
    Location:
    CA
    Vehicle:
    2021 Prius Prime
    Model:
    XLE
    Well I tried these Hella horns and didn't like the sound ..looks I might use the freeway blaster that I used on my Gen 3 or put in the Highlander horn.

    81hKoNIoD1L._AC_SL1500_.jpg
     
  16. FredtheWhale

    FredtheWhale New Member

    Joined:
    Jun 4, 2021
    3
    2
    0
    Location:
    New Jersey
    Vehicle:
    2021 Prius Prime
    Model:
    Limited
    Hi. I’m trying to replace my horn on a 2021 prime. Can anyone tell me where to buy a pigtail connector to fit the one that the original horn used? I know that i can snip the wires and reconnect.
     
  17. chickenhawk

    chickenhawk Member

    Joined:
    Sep 13, 2011
    261
    95
    8
    Location:
    CA
    Vehicle:
    2021 Prius Prime
    Model:
    XLE
    What happened to the original connector?
     
  18. FredtheWhale

    FredtheWhale New Member

    Joined:
    Jun 4, 2021
    3
    2
    0
    Location:
    New Jersey
    Vehicle:
    2021 Prius Prime
    Model:
    Limited
    The male side is built into the plastic housing of the oem horn.