1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Glue/paste squeezing out from the engine.

Discussion in 'Gen 3 Prius Care, Maintenance & Troubleshooting' started by LulzChicken, Jan 6, 2012.

Page 1 of 2
  1. LulzChicken

    LulzChicken Prius Enthusiast

    Joined:
    Jul 19, 2009
    791
    135
    0
    Location:
    Alabama
    Vehicle:
    2010 Prius
    Model:
    II
    Hey guys - I recently saw what appears to be glue or some type of paste coming out of my engine. I think it may have been there the entire life of the car, but I'm not sure. Is this something I should be worried about, or should I let it slide?
    [​IMG]
     
    #1 LulzChicken, Jan 6, 2012
  2. rrg

    rrg Active Member

    Joined:
    May 18, 2010
    458
    120
    41
    Location:
    East coast - NJ
    Vehicle:
    2011 Prius
    Model:
    Two
    Mine is the same way, almost in the same spot just over to the left of there.
     
    #2 rrg, Jan 6, 2012
    1 person likes this.
  3. frodoz737

    frodoz737 Top Wrench

    Joined:
    Aug 26, 2010
    4,297
    2,347
    33
    Location:
    Texas
    Vehicle:
    2015 Prius
    Model:
    Four
    Looks like RTV Gasket (sealant).
     
    #3 frodoz737, Jan 6, 2012
    1 person likes this.
  4. Colm--

    Colm-- New Member

    Joined:
    Nov 10, 2011
    12
    2
    0
    Location:
    Delaware
    Vehicle:
    2010 Prius
    Model:
    Two
    frodoz737 is correct. That's sealant applied where the perimeter seal overlaps.
     
    #4 Colm--, Jan 6, 2012
    1 person likes this.
  5. LulzChicken

    LulzChicken Prius Enthusiast

    Joined:
    Jul 19, 2009
    791
    135
    0
    Location:
    Alabama
    Vehicle:
    2010 Prius
    Model:
    II
    Thank you guys for the input. Should I have them do anything about this? I don't want more issues arising from them trying to fix it if I can just leave it alone.
     
    #5 LulzChicken, Jan 6, 2012
  6. qbee42

    qbee42 My other car is a boat

    Joined:
    Mar 2, 2006
    18,058
    3,073
    7
    Location:
    Northern Michigan
    Vehicle:
    2006 Prius
    Leave it alone.

    Tom
     
    #6 qbee42, Jan 6, 2012
    1 person likes this.
  7. LulzChicken

    LulzChicken Prius Enthusiast

    Joined:
    Jul 19, 2009
    791
    135
    0
    Location:
    Alabama
    Vehicle:
    2010 Prius
    Model:
    II
    That's just what I'll do! Thanks! Could I pull off the gunk that squeezed out, though, so it doesn't look bad?
     
    #7 LulzChicken, Jan 6, 2012
  8. spiderman

    spiderman wretched

    Joined:
    Jul 5, 2009
    7,543
    1,558
    0
    Location:
    Alaska
    Vehicle:
    2010 Prius
    Model:
    II
    take a razor blade and carefully cut it off flush with the block...
     
    #8 spiderman, Jan 6, 2012
    1 person likes this.
  9. BlizzardPearlV

    BlizzardPearlV Junior Member

    Joined:
    Nov 27, 2011
    35
    0
    0
    Location:
    Canada
    Vehicle:
    2012 Prius v wagon
    Model:
    N/A
    ^this!
     
    #9 BlizzardPearlV, Jan 6, 2012
  10. LulzChicken

    LulzChicken Prius Enthusiast

    Joined:
    Jul 19, 2009
    791
    135
    0
    Location:
    Alabama
    Vehicle:
    2010 Prius
    Model:
    II
    I just can't believe I wouldn't have noticed this earlier from all the time I have looked at my engine compartment. This would have had to of happened during manufacturing, right? As in, it would have had to be there the life of the car, am I right? I just hope it doesn't cause any problems. I just don't recall that being there, and I don't know why it all of a sudden oozed out.
     
    #10 LulzChicken, Jan 6, 2012
  11. HyperFX

    HyperFX NIMFY (not in my front yard)

    Joined:
    Nov 18, 2011
    81
    35
    30
    Location:
    New Jersey
    Vehicle:
    2011 Prius
    Model:
    Two
    Although it may be tempting, do not place it on a toothbrush and do not brush your teeth with it.
     
    #11 HyperFX, Jan 6, 2012
    3 people like this.
  12. Feri

    Feri Active Member

    Joined:
    Jun 25, 2011
    761
    144
    0
    Location:
    Maldon Victoria Australia
    Vehicle:
    2010 Prius
    Model:
    III
    Mine has it too. Purchased in Australia.
     
    #12 Feri, Jan 7, 2012
    1 person likes this.
  13. frodoz737

    frodoz737 Top Wrench

    Joined:
    Aug 26, 2010
    4,297
    2,347
    33
    Location:
    Texas
    Vehicle:
    2015 Prius
    Model:
    Four
    It's been there since the engine assembly was put together. Forget about it.
     
    #13 frodoz737, Jan 7, 2012
    1 person likes this.
  14. Judgeless

    Judgeless Senior Member

    Joined:
    Jun 30, 2009
    1,821
    255
    0
    Location:
    Cleveland, OH
    Vehicle:
    2010 Prius
    Model:
    IV
    First I would like to thank you for posting a pic of the issue. Way to many people post things like this without a pic. Everyone has a cell phone with a camera, why not use it.

    Here is a pic of mine.

    [​IMG]

    Mine looks identical except my engine is showing a lot more wear after 73,000 miles in Cleveland’s salty winters.
     
    #14 Judgeless, Jan 7, 2012
    1 person likes this.
  15. LulzChicken

    LulzChicken Prius Enthusiast

    Joined:
    Jul 19, 2009
    791
    135
    0
    Location:
    Alabama
    Vehicle:
    2010 Prius
    Model:
    II
    Great! This is re-assuring to me. I'll just leave it be. Thank you for posting guys! Everyone who posts in my thread gets a "Thanks"! Also, Judgeless, I agree. A picture is so much better than just words alone. There isn't much of an excuse NOT to include a picture now days. Cheers!
     
    #15 LulzChicken, Jan 7, 2012
  16. adamace1

    adamace1 Senior Member

    Joined:
    Jun 22, 2009
    1,403
    191
    0
    Location:
    Charlotte, NC
    Vehicle:
    2010 Prius
    Model:
    II
    Mine is the same way. Normal
     
    #16 adamace1, Jan 7, 2012
  17. rrg

    rrg Active Member

    Joined:
    May 18, 2010
    458
    120
    41
    Location:
    East coast - NJ
    Vehicle:
    2011 Prius
    Model:
    Two
    I took a second look. It is exactly like yours. Don't cut, it leave it.

    If you want, on your next dealer visit make them put a comment on your account that you have this and if any thing happens you have a record of it before the expiration of 36,000 miles.
     
    #17 rrg, Jan 7, 2012
  18. Mendel Leisk

    Mendel Leisk Senior Member

    Joined:
    Oct 17, 2010
    54,661
    38,205
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    It's normal; I'd leave it as-is. Liquid gasket of some sort has been applied to a joint. The only way to ensure none squeezes out is to not apply enough.
     
    #18 Mendel Leisk, Jan 10, 2012
  19. The Electric Me

    The Electric Me Go Speed Go!

    Joined:
    May 22, 2009
    9,083
    5,796
    0
    Location:
    Undisclosed Location
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A
    Just a comment to those saying leave it.

    If it's just a lump that has squeazed out and is hanging there? As it appears in the photos. Why would cutting it and removing it hurt anything? It obviously isn't doing anything just hanging there.

    I wouldn't worry about it. But I'd remove it.
     
    #19 The Electric Me, Jan 10, 2012
  20. Den49

    Den49 Member

    Joined:
    Oct 25, 2010
    498
    267
    0
    Location:
    Maryland
    Vehicle:
    2010 Prius
    Model:
    IV
    The "squeeze-out" of this type of form-a-gasket material is intended. It acts as a lock to prevent the gasket from shifting or loosening and leaking.

    Don't cut it off.
     
    #20 Den49, Jan 10, 2012
(You must log in or sign up to post here.)
Page 1 of 2