TPMS light confusion

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by splitter, May 27, 2026 at 7:26 PM.

Tags:
  1. splitter

    splitter Junior Member

    Joined:
    Jun 21, 2024
    16
    7
    0
    Location:
    NY
    Vehicle:
    2008 Prius
    Model:
    Three
    Hi everyone!

    I have a confusion about the TPMS light.

    Two TPMS sensors have gone on my wife's 2006 Prius - the TPMS light flashed on start then eventually settled on solid.

    I bought 4 Denso "OEM fit" sensors from RockAuto hoping to save a bit of money (DENSO 5500103) and have booked in at a local shop to have them fitted. They seemed a little confused about whether they would need to "program" them or not (they are pre-programmed I believe).

    To save some time and confusion, I decided to add the new sensor IDs to the car via TechStream before the new sensors are fitted.

    After doing this, the TPMS light has turned off. The sensors are still in the box, not installed. I drove round for 15 or so minutes, and the light did not come back on.

    I'm very confused about this. I would have thought that with the new sensor IDs on the car, the TPMS light would again be on since they can't be showing any pressure.

    Have I misunderstood something about this procedure?

    Bonus question: Anyone familiar with whether these particular sensors need to be "activated", e.g. tpms tool trigger, rapid deflate/inflate cycle?
     
    #1 splitter, May 27, 2026 at 7:26 PM
  2. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,888
    8,625
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    If you put in new sensor codes, you can confuse the computer for about half an hour, if your drive exceeds that, your light will come back on
     
    #2 JC91006, May 27, 2026 at 7:41 PM
    PriusCamper likes this.
  3. rjparker

    rjparker Tu Humilde Sirviente

    Joined:
    Jun 6, 2008
    10,746
    6,741
    7
    Location:
    Texas Hill Country
    Vehicle:
    2012 Prius v wagon
    Model:
    Three
    They don't need to be activated. They have motion detectors to turn them on.
     
    #3 rjparker, May 27, 2026 at 11:35 PM
  4. Mendel Leisk

    Mendel Leisk MMX GEN III

    Joined:
    Oct 17, 2010
    61,222
    42,090
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    The car needs to be programmed to recognize the new sensors, hopefully possible with what you’ve got. Both prepurchasing the sensors and the “confused” shop does not bode well. It’d be preferable to go with a shop that’ll do “turnkey”, knows their stuff and supplies/guarantees the sensors.
     
    #4 Mendel Leisk, May 28, 2026 at 8:57 AM
  5. splitter

    splitter Junior Member

    Joined:
    Jun 21, 2024
    16
    7
    0
    Location:
    NY
    Vehicle:
    2008 Prius
    Model:
    Three
    My understanding with the "OEM" Denso sensors is that they don't need to be programmed. Instead, you just need to install and activate them (or maybe not...) and then add their IDs to the TPMS ECU via TechStream. I can do the latter step. I need the shop to install them (and possible activate them).

    On a related note, I drove around for nearly 40 minutes this morning and the TPMS light has still not come back on. I also turned the car off / on multiple times to try to force a reset. I find this very confusing. The IDs saved in the car's ECU are the new sensor IDs which are still in the box on the passenger seat. So the TPMS light should be on. Either it takes forever for the car to recheck the sensors, or I've stumbled across a way to disable the TPMS light, perhaps along the lines of this thread: Techstream and TPMS - ClubLexus - Lexus Forum Discussion
     
    #5 splitter, May 28, 2026 at 9:02 AM
    Mendel Leisk likes this.
  6. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,888
    8,625
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    I've had this same feeling when I changed the sensor ID. Trust me, it'll come back on. If it were only that easy to disable a TPMS light, we would forget about using sensors altogether
     
    #6 JC91006, May 28, 2026 at 10:09 AM
  7. PrimalPrius

    PrimalPrius Member

    Joined:
    Nov 21, 2018
    135
    11
    0
    Location:
    America
    Vehicle:
    2009 Prius
    Model:
    Base
    A fairly easy DIY. Tighten a 2" cargo strap around the perimeter of the tire, set some 2x lumber on the floor so that it touches the tire but not the rim and jump on the rim to break the bead. Use a fishing line or string when removing the old sensor and installing the new one. A tool like this makes that step easier: More Information for PERFORMANCE TOOL 60501.
    To reseat the bead just adding air often works for me. Remove valve stem before air if it won't seat with the valve stem in place.
     
    #7 PrimalPrius, May 28, 2026 at 12:10 PM
  8. rjparker

    rjparker Tu Humilde Sirviente

    Joined:
    Jun 6, 2008
    10,746
    6,741
    7
    Location:
    Texas Hill Country
    Vehicle:
    2012 Prius v wagon
    Model:
    Three
    Most likely the id programming in the car's ecu is done (as you indicated much earlier), the sensor motion detectors turn them on (activate not the proper word) and "possibly" you set the tpms alarm point at zero.

    prius tpms 2023-09-18.jpeg

    Unfortunately we have members offering advice who don't read the thread (just reading the ops posts is all that is necessary) or members who have never done the subject.
     
    #8 rjparker, May 28, 2026 at 1:07 PM
    Last edited: May 28, 2026 at 1:18 PM
(You must log in or sign up to post here.)