12v battery terminal connector access

Discussion in 'Prius c Main Forum' started by pasta4breakfast, Mar 31, 2026 at 1:23 AM.

  1. pasta4breakfast

    Joined:
    Mar 8, 2020
    116
    55
    0
    Location:
    Anaheim, CA
    Vehicle:
    2020 Prius Prime
    Model:
    LE
    I recently bought an 12v battery jumper pack. I wanted to make sure I could easily access the 12v battery before actually needing to. The space between the two terminals are so cramped that I can't get both cables to fully clamp around the terminal connectors. Would it be okay to connect it to the bolts/nuts as shown in the image instead of fully around the terminal connectors? Has anyone had to do this before and been able to jump start their prius C?

    upload_2026-3-30_21-59-14.jpeg
     

    Attached Files:

  2. BiomedO1

    BiomedO1 Senior Member

    Joined:
    Mar 27, 2021
    4,159
    2,179
    0
    Location:
    SacTown, Ca
    Vehicle:
    2021 Prius Prime
    Model:
    LE
    Why not just use the jump point under the hood; rather than rip out the access panel under the seat???o_O:sleep:
     
    John in Vermont likes this.
  3. pasta4breakfast

    Joined:
    Mar 8, 2020
    116
    55
    0
    Location:
    Anaheim, CA
    Vehicle:
    2020 Prius Prime
    Model:
    LE
    The cables are very short. I couldn't reach the spot that was recommended to connect the negative cable clamp to.
     
  4. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    28,051
    18,556
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    The car has a negative-ground electrical system, so pretty much any unpainted metal you can reach with the clamp will do the trick. I've never tried to jump a Prius c, but I also can't remember in any car ever having to look very hard for a place to clamp the ground.
     
    pasta4breakfast and BiomedO1 like this.
  5. BiomedO1

    BiomedO1 Senior Member

    Joined:
    Mar 27, 2021
    4,159
    2,179
    0
    Location:
    SacTown, Ca
    Vehicle:
    2021 Prius Prime
    Model:
    LE
    ^That or preemptively install a short ground jump wire and tuck it away. That's what I did for my old 2012 Prius C.:D:cool::p:whistle:
     
  6. Mendel Leisk

    Mendel Leisk MMX GEN III

    Joined:
    Oct 17, 2010
    60,913
    41,912
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    Early production c's didn't have a jump point; was a real design fail, considering the battery location. @pasta4breakfast doesn't disclose his year though,.

    If there's no under-hood jump point, maybe just wire in some sort of quick-connect??
     
  7. rjparker

    rjparker Tu Humilde Sirviente

    Joined:
    Jun 6, 2008
    10,527
    6,608
    7
    Location:
    Texas Hill Country
    Vehicle:
    2012 Prius v wagon
    Model:
    Three
    I carry a 2 foot #6 home made jumper with good size alligator clips in our Rav4 hybrid to avoid the "easy" ecm frame ground which is known to blow the ecm on occasion.

    However it has seen more use when providing a jump to big pickup trucks.
     
    #7 rjparker, Mar 31, 2026 at 12:46 PM
    Last edited: Mar 31, 2026 at 2:11 PM
    BiomedO1 likes this.
  8. PriusTech

    PriusTech Active Member

    Joined:
    Jan 13, 2011
    261
    120
    14
    Location:
    Reno
    Vehicle:
    2005 Prius
    Model:
    N/A
    clamping the nuts is fine, even though there's not as much contact area, it can still work. Wiggle it around if it doesn't work right away. Look in the owners manual, it may show a clamp point in the underhood fuse box.

    One of the big problems with a 2nd gen is if you stash your jumper cables in the trunk by the spare you can't get at them when the battery is dead, because the trunk only opens electrically. So I stash my cables under one of the front seats, because you can get at them with the mechanical key to open the door.

    Just another simple thing overlooked by the genius Japan engineers. They were so focused on building the most technologically advanced vehicle of it's time, they missed some of the small simple things.
     
    pasta4breakfast likes this.
  9. BiomedO1

    BiomedO1 Senior Member

    Joined:
    Mar 27, 2021
    4,159
    2,179
    0
    Location:
    SacTown, Ca
    Vehicle:
    2021 Prius Prime
    Model:
    LE
    As I recall; it was a very skinny jump point - those clamps pictured above won't clip-on. My solution was two quality alligator clips, then clip onto the alligator clips. It wasn't pretty, but it works. No getting on your knees and fighting the lower seat panel cover.
    Another idea is to run a couple of short jumper wires from the battery and drill a couple of holes in the plastic cover to put a bolt through. You can just clip onto the protruding bolt heads to jump. The bolts will need to be far enough apart so that there's no accidental bridging of the two points. As I recall; that access panel was a bit of a pain to remove; with my tool box next to me. I can only imagine the pain, in a parking lot or side of the road w/o tools.

    YMMV
     
    Mendel Leisk and PriusTech like this.
  10. Mendel Leisk

    Mendel Leisk MMX GEN III

    Joined:
    Oct 17, 2010
    60,913
    41,912
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    Sounds about right. Found this.
     
  11. pasta4breakfast

    Joined:
    Mar 8, 2020
    116
    55
    0
    Location:
    Anaheim, CA
    Vehicle:
    2020 Prius Prime
    Model:
    LE
    Thanks for all of the ideas. It is a 2013 prius C. I believe there is a positive terminal in the fuse box under the hood. I didn't think to use it because the videos I saw showed people connecting the negative clamp to a point on the other side of the engine bay. I knew I wouldn't be able to reach that with my tiny cables/clamps. Looking at my engine bay below, I should be able to reach the bracket on the corner of the inverter assesmbly closest to the fuse box. Would that be safer or at least as safe as playing around with the battery in that cramped location?
    upload_2026-3-31_20-38-11.jpeg
     

    Attached Files:

    BiomedO1 likes this.
  12. Mendel Leisk

    Mendel Leisk MMX GEN III

    Joined:
    Oct 17, 2010
    60,913
    41,912
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    Visual aid, for anyone wondering where the Prius c fuse box is:

    IMG_3548.jpeg

    You can verify if an alternate ground point is indeed grounded, with a multimeter set to ohms or continuity, or with a test light:

    IMG_3549.jpeg
     
  13. rjparker

    rjparker Tu Humilde Sirviente

    Joined:
    Jun 6, 2008
    10,527
    6,608
    7
    Location:
    Texas Hill Country
    Vehicle:
    2012 Prius v wagon
    Model:
    Three
    Don't forget that not all ground points are safe to use, particularly frames of ecus.
     
    Mendel Leisk likes this.
  14. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    28,051
    18,556
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    Under the hood of every Prius model I've worked on, the fusebox with the positive jump point is within even a pretty short cable reach of the inverter assembly, which is a stout aluminum grounded case that also contains the source of the car's 12-volt power system. I generally just clamp on there and get on with things.